The Austin-Healey 3000 is a British sports car built from 1959 to 1967, and is the best known of the “big Healey” models. The car’s bodywork was made by Jensen Motors, and the vehicles were assembled by Austin-Healey at the Abingdon works. The Austin-Healey 3000 was introduced in 1959, replacing the Austin-Healey 100-6. Despite its new name, the changes were minor compared to those between the original 100 and the 100-6. The wheelbase and body were unchanged, as were the models, a 2+2 and a two-seater. The 3-litre 3000 was a highly successful car, which won its class in many European rallies in its heyday and is still raced in classic car competitions by enthusiasts today.
Frequently Asked Questions
How do I adjust the clutch on my Austin Healey 3000?
To adjust the clutch on your Austin Healey 3000, first locate the clutch slave cylinder at the side of the gearbox. Loosen the lock nut and turn the adjuster rod clockwise to increase clutch free play or counterclockwise to decrease it. Tighten the lock nut when finished and check the clutch pedal for proper operation.
How do I adjust the valve clearance on my Austin Healey 3000?
To adjust the valve clearance on your Austin Healey 3000, first remove the valve cover and locate the adjuster screws on the rocker arms. Using a feeler gauge, adjust the clearance to the recommended specification for your engine. Finally, replace the valve cover and check for proper operation.
How do I bleed the brakes on my Austin Healey 3000?
To bleed the brakes on your Austin Healey 3000, begin at the wheel farthest from the master cylinder and work your way closer. Remove the rubber cap from the bleeder valve and attach a clear plastic hose to the valve. Have a helper press the brake pedal while you open the valve to allow air and brake fluid to escape. Repeat this process until no air bubbles are present in the brake fluid.
How do I change the oil in my Austin Healey 3000?
Changing the oil in your Austin Healey 3000 is a straightforward process. Begin by draining the old oil from the oil pan. Remove and replace the oil filter. Finally, pour in the recommended amount of new oil and replace the oil cap.
How do I check the transmission fluid level in my Austin Healey 3000?
To check the transmission fluid level in your Austin Healey 3000, first ensure that the car is level. Remove the dipstick located on the side of the transmission and wipe it clean with a cloth. Reinsert the dipstick and remove it again to check the level. The transmission fluid level should be between the “add” and “full” marks on the dipstick.
How do I replace the air filter in my Austin Healey 3000?
To replace the air filter in your Austin Healey 3000, begin by removing the air filter cover. Remove the old air filter and replace it with a new one. Finally, replace the air filter cover and check for proper operation.
How do I replace the battery in my Austin Healey 3000?
To replace the battery in your Austin Healey 3000, begin by disconnecting the negative battery cable. Remove the hold-down clamp and remove the old battery. Install the new battery, being careful to connect the positive and negative cables to the correct terminals. Finally, reattach the hold-down clamp and check for proper operation.
How do I replace the brake pads on my Austin Healey 3000?
To replace the brake pads on your Austin Healey 3000, first remove the wheel and caliper from the brake assembly. Remove the old brake pads and replace them with new ones. Finally, reattach the caliper and wheel and check for proper operation.
How do I replace the brake shoes on my Austin Healey 3000?
To replace the brake shoes on your Austin Healey 3000, first remove the wheel and brake drum. Remove the old brake shoes and replace them with new ones, being careful to adjust the brake shoes to the proper clearance. Finally, reattach the brake drum and wheel and check for proper operation.
How do I replace the fuel filter in my Austin Healey 3000?
To replace the fuel filter in your Austin Healey 3000, first locate the fuel filter near the fuel pump. Loosen the hose clamps and remove the old filter. Install the new filter and tighten the hose clamps. Finally, check for proper operation.
How do I replace the spark plugs in my Austin Healey 3000?
To replace the spark plugs in your Austin Healey 3000, begin by removing the spark plug wire from the old plug. Use a spark plug socket to remove the old plug and replace it with a new one, being careful not to overtighten it. Finally, reattach the spark plug wire to the new plug.
How do I troubleshoot an electrical problem in my Austin Healey 3000?
To troubleshoot an electrical problem in your Austin Healey 3000, begin by checking the fuses and relays for proper operation. Check the battery and alternator for proper voltage output. Finally, use a multimeter to test the wiring for continuity and proper grounding.
What kind of spark plugs should I use in my Austin Healey 3000?
It is recommended to use NGK BP6ES spark plugs in your Austin Healey 3000. These are high-quality spark plugs that will provide reliable ignition and long service life.
What type of oil should I use in my Austin Healey 3000?
It is recommended to use a high-quality mineral-based oil with a viscosity of 20W50 for your Austin Healey 3000. Synthetic oils are not recommended as they may cause oil leaks due to the different properties of synthetic oils.
Austin Healey 3000 Related Models