Lexus NX 200 Free Workshop and Repair Manuals

To adjust the side mirrors on a Lexus NX 200, locate the mirror adjustment switch on the driver’s door panel. Use the switch to select the desired mirror (left or right) by pressing the corresponding side of the switch. Once the desired mirror is selected, use the switch to adjust the mirror position vertically, horizontally, or diagonally until you achieve the desired field of view. The mirrors can be adjusted while the vehicle is stationary or during driving, but it is recommended to make adjustments when the vehicle is safely parked.

To change the oil in a Lexus NX 200, start by locating the oil drain plug underneath the vehicle and placing a drain pan beneath it. Remove the drain plug to let the old oil drain out completely. Once the oil has drained, replace the drain plug and remove the oil filter. Install a new oil filter, then refill the engine with the recommended amount and type of oil specified in the vehicle’s manual. Be sure to properly dispose of the used oil and filter in an environmentally-friendly manner.

To check and top up the brake fluid in a Lexus NX 200, locate the brake fluid reservoir, which is usually located on top of the brake master cylinder near the firewall. Ensure the vehicle is parked on a level surface and the engine is off. Remove the reservoir cap and check the fluid level against the “MAX” and “MIN” markings on the side of the reservoir. If the fluid level is below the “MIN” marking, add the recommended brake fluid type gradually to avoid spilling. Use a funnel if necessary. Be careful not to overfill the reservoir, as it can cause brake fluid leakage or other issues.

To check the transmission fluid in a Lexus NX 200, start the engine and allow it to idle for a few minutes to warm up the transmission. Locate the transmission dipstick, which is usually labeled and located near the back of the engine bay. Pull out the dipstick, wipe it clean, reinsert it fully, and then pull it out again. Check the fluid level on the dipstick against the markings, ensuring it falls within the recommended range. If needed, add the recommended type of transmission fluid through the dipstick tube using a funnel.

To jump-start a Lexus NX 200, you will need a set of jumper cables and a second vehicle with a charged battery. Park the second vehicle close enough to the Lexus NX 200 so that the jumper cables can reach both batteries. Turn off the ignition in both vehicles and connect the positive (+) terminal of the dead battery to the positive terminal of the charged battery. Then, connect the negative (-) terminal of the charged battery to a metal part of the engine block in the Lexus NX 200. Start the second vehicle and let it run for a few minutes, then attempt to start the Lexus NX 200. Once the vehicle has started, carefully disconnect the jumper cables in the reverse order.

To replace a cabin air filter in a Lexus NX 200, locate the cabin air filter housing, which is typically located behind the glove box. Open the glove box and remove any contents. Squeeze the sides of the glove box inward to release the stops and allow it to fully drop down. Locate the cabin air filter housing cover and remove the screws or clips holding it in place. Take out the old filter and replace it with a new one, ensuring it is properly aligned. Reinstall the housing cover, raise the glove box back into place, and secure it by pushing the sides inward until the stops engage.

To replace a headlight bulb in a Lexus NX 200, start by opening the hood and locating the back of the headlight assembly. Remove the electrical connector by pressing the release tab and pulling it away from the bulb. Twist the bulb counterclockwise to remove it from the socket. Insert the new bulb into the socket and twist it clockwise to secure it. Reconnect the electrical connector and test the new bulb by turning on the headlights.

To replace a windshield wiper blade on a Lexus NX 200, lift the wiper arm away from the windshield until it locks into the raised position. Locate the release tab on the wiper blade connector and press it to release the old blade from the wiper arm. Slide the old blade out of the connector and slide the new blade in until it clicks into place. Slowly lower the wiper arm back onto the windshield. Repeat the process for the other wiper blade, if necessary.

To replace the battery in a Lexus NX 200 key fob, start by locating the small notch on the side of the key fob. Use a small flat-head screwdriver or a coin to gently pry open the key fob. Once opened, carefully remove the old battery and replace it with a new one of the same type. Ensure the battery is properly seated, then snap the key fob back together. Test the key fob to ensure it is functioning correctly.

To reset the maintenance light on a Lexus NX 200, turn the ignition switch to the “ON” position without starting the engine. Within a few seconds, locate and press the “TRIP” button on the instrument cluster repeatedly until the odometer reading is displayed. Turn the ignition switch to the “OFF” position, then press and hold the “TRIP” button while turning the ignition switch back to the “ON” position. Continue holding the “TRIP” button until the maintenance light goes off and the odometer reading returns. Release the “TRIP” button, and the maintenance light should be successfully reset.

To troubleshoot a malfunctioning power window in a Lexus NX 200, start by checking the window switch to ensure it is not stuck or damaged. If the switch appears to be functioning correctly, check the fuse related to the power windows in the vehicle’s fuse box. If the fuse is blown, replace it with a new one of the same rating. If the switch and fuse are in working order, the issue may be with the window motor or regulator, which may require professional inspection and repair.

The air filter in a Lexus NX 200 should be replaced according to the manufacturer’s recommended maintenance schedule, which can be found in the owner’s manual. As a general guideline, it is typically recommended to replace the air filter every 15,000 to 30,000 miles or every 12 to 24 months, depending on driving conditions. Regular air filter replacements help maintain proper engine performance, fuel efficiency, and prolong the life of the engine.

The recommended coolant for a Lexus NX 200 is a 50/50 mixture of ethylene glycol-based antifreeze and distilled water. This coolant mixture provides optimal protection against freezing and overheating, as well as corrosion prevention for the engine and cooling system components. It is important to use the correct coolant type and maintain the coolant level within the recommended range to ensure proper engine cooling and prevent potential damage.

The recommended tire pressure for a Lexus NX 200 can be found in the owner’s manual or on the sticker located on the driver’s side door jamb. It is important to maintain the correct tire pressure to ensure optimal handling, fuel efficiency, and tire longevity. Underinflated tires can lead to increased rolling resistance, decreased fuel efficiency, and uneven tire wear, while overinflated tires can negatively impact ride comfort and traction.