The Rover Metro is a car manufactured by Rover Group from 1990 until 1995. In many export markets, including Italy and France, the Rover Metro was badged as the Rover 100 series, with the 1.1 known as the Rover 111 and the 1.4 called 114. This model was in production from 1994 until 1998. It was produced with 1.4 cc K-Series 8 valve engines and a 16 valve engine in the GTa. All models used a joint Rover Peugeot designed end-on gearboxes. General build quality, fit and finish was improved enormously from the old Metro and went on to win What Car “Car of The Year” in 1991.
Frequently Asked Questions
How do I bleed the brake system in my Rover 114?
To bleed the brake system in your Rover 114, start with the brake furthest from the master cylinder (usually the rear passenger side). Attach a clear plastic hose to the bleeder valve and place the other end in a container partially filled with brake fluid. Have someone pump the brake pedal several times, then hold it down. Open the bleeder valve to release any air or old fluid, and close it once the pedal reaches the floor. Repeat this process on each brake until all air bubbles are eliminated.
How do I change the oil in my Rover 114?
To change the oil in your Rover 114, start by locating the oil drain plug underneath the engine. Remove the drain plug and let the old oil drain completely. Once drained, replace the drain plug and refill the engine with the recommended amount and type of oil specified in the manual.
How do I check the tire pressure in my Rover 114?
To check the tire pressure in your Rover 114, first, ensure that the tires are cold. Locate the valve stem on each tire and remove the valve cap. Use a tire pressure gauge to measure the pressure by pressing the gauge firmly onto the valve stem. Compare the measured pressure to the recommended tire pressure specified in the manual. If the pressure is too low, add air, and if it is too high, release some air until the correct pressure is achieved.
How do I diagnose a malfunctioning power window in my Rover 114?
If you are experiencing issues with a power window in your Rover 114, start by checking the fuse associated with the power window circuit. If the fuse is intact, inspect the window switch for any signs of damage or wear. Test the window regulator and motor by applying direct power to them to determine if they are functioning correctly. If necessary, replace the faulty component or seek professional assistance for further diagnosis.
How do I replace a damaged wheel bearing in my Rover 114?
To replace a damaged wheel bearing in your Rover 114, first, raise the vehicle and secure it on jack stands. Remove the wheel and brake components that obstruct access to the wheel bearing. Disconnect the wheel speed sensor if applicable, then remove the hub assembly from the steering knuckle. Press out the old wheel bearing from the hub and press in the new one using a suitable tool. Finally, reassemble the components in the reverse order and torque them to the recommended specifications.
How do I replace a faulty fuel pump in my Rover 114?
To replace a faulty fuel pump in your Rover 114, first, relieve the fuel system pressure by disconnecting the fuel pump fuse or relay and starting the engine until it stalls. Disconnect the negative battery cable and locate the fuel pump, which is typically located inside the fuel tank. Remove any necessary components that obstruct access to the fuel pump, then disconnect the electrical connectors and fuel lines. Finally, remove the old fuel pump and install the new one, following the reverse steps.
How do I replace a faulty oxygen sensor in my Rover 114?
To replace a faulty oxygen sensor in your Rover 114, first, locate the sensor, which is typically positioned in the exhaust system. Disconnect the electrical connector from the sensor, then use an oxygen sensor socket or a wrench to remove the old sensor. Apply anti-seize compound to the threads of the new sensor, then install it and tighten it to the specified torque. Finally, reconnect the electrical connector to the new sensor.
How do I replace a headlight bulb in my Rover 114?
To replace a headlight bulb in your Rover 114, locate the back of the headlight assembly and carefully disconnect the electrical connector. Remove the retaining clip or screws holding the bulb in place, then remove the old bulb. Insert the new bulb, secure it with the retaining clip or screws, and reconnect the electrical connector.
How do I replace a worn serpentine belt in my Rover 114?
To replace a worn serpentine belt in your Rover 114, locate the belt tensioner and use a wrench or a specialized tool to relieve the tension on the belt. Slip the belt off the pulleys and carefully route the new belt around the pulleys, following the correct pattern as shown in the manual. Finally, release the tensioner to apply proper tension to the new belt.
How do I replace the cabin air filter in my Rover 114?
To replace the cabin air filter in your Rover 114, locate the filter housing, which is typically located behind the glove compartment or under the dashboard. Remove the housing cover or access panel, then take out the old filter. Insert the new filter in the correct orientation as indicated by the arrows or instructions on the filter. Finally, secure the housing cover or access panel back in place.
How do I reset the service indicator on my Rover 114?
To reset the service indicator on your Rover 114, insert the key into the ignition and turn it to the “on” position without starting the engine. Press and hold the mileage reset button or the trip meter reset button, depending on the model, until the service indicator begins to flash or reset to zero. Release the button and start the engine to confirm that the service indicator has been successfully reset.
How do I troubleshoot a faulty ignition system in my Rover 114?
If you are experiencing issues with your Rover 114’s ignition system, start by checking the battery’s charge level and connections. Next, inspect the spark plugs and ignition coils for any signs of damage or wear. Additionally, ensure that the fuel pump is functioning properly and that the engine’s timing is correctly set. If the problem persists, it is advisable to consult the Rover 114 manual for specific troubleshooting steps or seek professional assistance.
How often should I replace my Rover 114’s air filter?
It is recommended to replace the air filter in your Rover 114 every 12,000 to 15,000 miles or as specified in the manual. However, if you frequently drive in dusty or polluted environments, it may be necessary to replace it more frequently. Regularly inspect the air filter and replace it when it appears dirty or clogged to ensure optimal engine performance and fuel efficiency.
What type of coolant should I use in my Rover 114?
It is recommended to use a high-quality, ethylene glycol-based coolant with the correct mixture of water as specified in the Rover 114 manual. This coolant should meet the required specifications to ensure proper cooling and protection against freezing and overheating. Be sure to consult the manual for the exact coolant type and mixture ratios for your specific model.
Rover 114 Related Models