The Bedford HA was a car derived van introduced in 1963 by Bedford, based on the Vauxhall Viva (HA) family car. It was also known as the Bedford Beagle in estate form and Bedford Roma in small campervan form. The Beagle was an officially sanctioned conversion based on the 8 cwt van, carried out by Martin Walter Ltd. (of Folkestone, Kent).The Beagle received rear side windows and a fold-down rear seat leaving 28 inches (710 mm) of luggage space with the seat in use. By the late seventies, the denominations had been changed to HA?110 and HA?130 respectively, with payload ratings of 371 and 546 kg (818 and 1,204 lb).[7] In September 1964, for the 1965 model year, the Viva and HA Van received minor changes such as a quicker steering rack, new door trim, and a modified choke control.[8] In Australia, the Bedford HA was sold as the “Bedford Handi-Van” from 1964 until 1970.
Frequently Asked Questions
How do I bleed the brake system on my Bedford HA?
To bleed the brake system on your Bedford HA, start with the wheel farthest from the master cylinder and work your way closer. Have a helper pump the brake pedal several times and then hold it down, while you open the bleeder valve with a wrench. Close the valve and repeat the process until all air bubbles have been removed from the system. Check the brake fluid level and top off as needed.
How do I change the oil on my Bedford HA?
Changing the oil on your Bedford HA requires draining the old oil from the oil pan and replacing the oil filter. The oil pan is located at the bottom of the engine and can be accessed by removing the drain plug. After draining the old oil, replace the drain plug and oil filter, and then refill the engine with the recommended amount and type of oil.
How do I replace the air filter on my Bedford HA?
To replace the air filter on your Bedford HA, locate the air filter housing and remove the cover. Remove the old air filter and inspect the housing for debris and damage. Install the new air filter and replace the cover, making sure it is securely fastened. A clogged air filter can reduce engine performance and fuel economy.
How do I replace the alternator on my Bedford HA?
To replace the alternator on your Bedford HA, disconnect the battery and remove any belts or hoses that may be in the way. Disconnect the electrical connections and mounting bolts, and then remove the old alternator. Install the new alternator and reattach the electrical connections and mounting bolts. A faulty alternator can cause battery failure and electrical system malfunctions.
How do I replace the brake pads on my Bedford HA?
To replace the brake pads on your Bedford HA, remove the wheels and calipers, and then replace the old pads with new ones. Make sure to properly lubricate the caliper pins and slide bolts, and check the brake rotors for wear and damage. Reinstall the calipers and wheels, and then pump the brake pedal several times to ensure proper braking performance.
How do I replace the cabin air filter on my Bedford HA?
To replace the cabin air filter on your Bedford HA, locate the filter housing under the dashboard or in the engine compartment. Remove the cover and take out the old filter, making note of its orientation. Install the new filter and replace the cover, making sure it is securely fastened. A clogged cabin air filter can reduce the effectiveness of your vehicle’s heating and cooling system.
How do I replace the fuel filter on my Bedford HA?
To replace the fuel filter on your Bedford HA, locate the filter housing and use a wrench to loosen the mounting bolts. Remove the old filter and install the new one, making sure to properly tighten the mounting bolts. Check for leaks and make sure the fuel system is properly pressurized before starting the engine.
How do I replace the serpentine belt on my Bedford HA?
To replace the serpentine belt on your Bedford HA, locate the belt routing diagram under the hood and use it to identify the tensioner pulley. Use a serpentine belt tool or a breaker bar and socket to release the tension on the belt, and then remove it from the pulleys. Install the new belt according to the diagram, and then check for proper tension and alignment.
How do I replace the spark plugs on my Bedford HA?
To replace the spark plugs on your Bedford HA, locate the spark plug wires and remove them from the spark plugs. Use a spark plug socket and ratchet to remove the old plugs, and then install the new plugs and tighten to the recommended torque specification. Reattach the spark plug wires and check for proper engine operation.
How do I replace the thermostat on my Bedford HA?
To replace the thermostat on your Bedford HA, locate the thermostat housing and use a wrench to remove the mounting bolts. Remove the old thermostat and inspect the housing for corrosion and leaks. Install the new thermostat and gasket according to the manufacturer’s instructions, and then reattach the housing and bolts. A malfunctioning thermostat can cause engine overheating and poor performance.
How do I replace the water pump on my Bedford HA?
To replace the water pump on your Bedford HA, locate the pump and use a wrench to remove the mounting bolts. Remove the old pump and inspect the housing for leaks and corrosion. Install the new pump and gasket according to the manufacturer’s instructions, and then reattach the mounting bolts. A malfunctioning water pump can cause engine overheating and damage.
What is the recommended coolant for my Bedford HA?
The recommended coolant for your Bedford HA is a 50/50 mixture of ethylene glycol and water. This mixture provides protection against freezing and overheating, and also helps prevent corrosion and rust. Check the coolant level regularly and top off as needed, and also inspect the radiator and hoses for leaks and damage.
What is the recommended oil filter for my Bedford HA?
The recommended oil filter for your Bedford HA will depend on the make and model of your vehicle. Consult the owner’s manual or a parts catalog for the correct filter part number, and make sure to choose a quality filter that meets or exceeds OEM specifications. A good quality oil filter will help protect your engine and prolong its life.
What is the recommended tire pressure for my Bedford HA?
The recommended tire pressure for your Bedford HA depends on the type of tire and the weight of the vehicle. Check the tire sidewall for the maximum pressure rating and adjust accordingly. Underinflated tires can cause poor fuel economy and premature tire wear, while overinflated tires can result in a harsh ride and reduced traction.
Bedford HA Related Models