Corvette C1 Workshop Manuals and Repair Manuals

Every Manual available online - found by our community and shared for FREE. Enjoy!

Corvette C1

The Chevrolet Corvette (C1) is the first generation of the sports car by the Chevrolet division of General Motors introduced late in the 1953 model year and produced through 1962. EX-122 pre-production Corvette prototype was first shown to the public at the 1953 General Motors Motorama at the Waldorf-Astoria in New York City on January 17, 1953. Production began six months later. The 1962 model year was the last Corvette with a solid-rear-axle suspension that was used from the beginning. With two new engines it was also the quickest. Engine displacement increased to 327 cubic inches, but dual 4-barrel carburetor engines were no longer available. In total, 69,015 units were produced.

Corvette C1 FAQ's

How do I adjust the clutch in a Corvette C1?

To adjust the clutch in a Corvette C1, locate the clutch linkage on the driver's side of the engine compartment. Loosen the locknut and turn the adjustment screw to adjust the free play in the clutch pedal. Tighten the locknut once the adjustment is complete. Proper clutch adjustment ensures smooth shifting and prevents premature clutch wear.

How do I adjust the timing on a Corvette C1?

To adjust the timing on a Corvette C1, locate the distributor on the front of the engine. Loosen the distributor hold down bolt and rotate the distributor to adjust the timing. Use a timing light to set the timing to the proper specification. Tighten the distributor hold down bolt once the timing is set. Proper timing ensures optimal engine performance.

How do I bleed the brakes on a Corvette C1?

To bleed the brakes on a Corvette C1, start with the brake farthest from the master cylinder and work your way closer. Have a helper pump the brake pedal several times and hold it down while you open the bleeder valve. Allow the brake fluid to flow until there are no more air bubbles. Repeat this process for each brake until the system is fully bled.

How do I change the transmission fluid in a Corvette C1?

To change the transmission fluid in a Corvette C1, locate the transmission pan underneath the vehicle. Remove the bolts holding the pan in place and carefully lower the pan to drain the old fluid. Clean the pan and replace the gasket. Refill the transmission with the recommended fluid, checking the level with the dipstick. Be sure to dispose of the old fluid properly.

How do I check the brake fluid level in a Corvette C1?

To check the brake fluid level in a Corvette C1, locate the brake fluid reservoir on the driver's side of the engine compartment. The fluid level should be between the MAX and MIN marks on the reservoir. If the level is low, add brake fluid to bring it up to the proper level. Be sure to use the recommended brake fluid for your Corvette C1.

How do I check the radiator coolant level in a Corvette C1?

To check the radiator coolant level in a Corvette C1, locate the radiator on the front of the engine compartment. Check the coolant level in the radiator by looking at the coolant level indicator on the side of the radiator. The coolant level should be between the MAX and MIN marks. If the level is low, add the recommended coolant to bring it up to the proper level.

How do I replace the air filter in a Corvette C1?

To replace the air filter in a Corvette C1, locate the air cleaner assembly on the driver's side of the engine compartment. Remove the wing nut and lift the air cleaner lid to access the air filter. Remove the old air filter and replace it with a new one, making sure it is properly seated in the air cleaner housing. Reassemble the air cleaner assembly.

How do I replace the battery in a Corvette C1?

To replace the battery in a Corvette C1, locate the battery on the passenger side of the engine compartment. Disconnect the negative terminal first, then the positive terminal. Remove the battery hold down bolt and carefully lift the battery out of the compartment. Install the new battery, tightening the hold down bolt. Reconnect the positive terminal first, then the negative terminal.

How do I replace the fuel filter in a Corvette C1?

To replace the fuel filter in a Corvette C1, locate the fuel filter on the passenger side of the engine compartment. Disconnect the fuel lines from the filter using a fuel line disconnect tool. Remove the old filter and install the new one, making sure the arrow on the filter points in the direction of fuel flow. Reconnect the fuel lines to the filter.

How do I replace the spark plugs in a Corvette C1?

To replace the spark plugs in a Corvette C1, locate the spark plug wires on the top of the engine. Carefully remove the wires from the spark plugs. Use a spark plug socket to remove the old spark plugs and replace them with new ones, torquing them to the proper specification. Reattach the spark plug wires in the correct order.

How do I replace the thermostat in a Corvette C1?

To replace the thermostat in a Corvette C1, locate the thermostat housing on the top of the engine. Remove the bolts holding the housing in place and carefully lift it off the engine. Remove the old thermostat and install the new one, making sure the spring side faces into the engine. Reinstall the housing and bolts, torquing them to the proper specification.

How do I replace the water pump in a Corvette C1?

To replace the water pump in a Corvette C1, drain the cooling system and remove the hoses from the water pump. Remove the bolts holding the water pump in place and carefully lift it off the engine. Clean the gasket surface and install the new water pump, torquing the bolts to the proper specification. Reattach the hoses and refill the cooling system.

What is the recommended tire pressure for a Corvette C1?

The recommended tire pressure for a Corvette C1 is 24 psi for the front tires and 26 psi for the rear tires. Proper tire pressure ensures even wear and handling performance. Be sure to check tire pressure regularly and adjust as needed.

What type of oil should be used in a Corvette C1?

A Corvette C1 should use SAE 30 weight oil for temperatures above 32 degrees Fahrenheit, and SAE 20 weight oil for temperatures below 32 degrees Fahrenheit. It is important to use high-quality oil to ensure proper lubrication and engine protection. Be sure to check oil levels regularly and change the oil according to the maintenance schedule.