Every Manual available online - found by our community and shared for FREE. Enjoy!
Debuted in the 2005 Chicago Auto show as a concept car featuring an aluminum themed interior design, the Dodge Nitro is a compact SUV from the Dodge division of Chrysler Corporation. Production started from 2007 and ended in 20 12 model year. It shared its platform with the second generation Jeep Liberty and it became the first compact SUV from Dodge since the discontinuation of Dodge Raider in 1990 .
Dodge Nitro FAQ's
How do I bleed the brakes on my Dodge Nitro?
To bleed the brakes on your Dodge Nitro, first, locate the brake bleeder valve on each wheel. Then, attach a clear plastic hose to the valve and place the other end in a container. Have a helper pump the brakes several times and hold the pedal down. Open the bleeder valve and allow the brake fluid to flow through the hose. Close the valve and repeat the process on each wheel until all air is removed from the system.
How do I change the oil in my Dodge Nitro?
To change the oil in your Dodge Nitro, first, lift the vehicle using a hydraulic jack and place it on jack stands. Then, locate the oil drain plug and remove it using a wrench. Allow the oil to drain completely before replacing the drain plug and refilling the engine with new oil.
How do I check the transmission fluid in my Dodge Nitro?
To check the transmission fluid in your Dodge Nitro, first, ensure that the vehicle is on a level surface and the engine is running. Then, locate the transmission dipstick, remove it, and wipe it clean. Reinsert the dipstick and remove it again to check the fluid level. The level should be between the low and high marks on the dipstick.
How do I diagnose a check engine light on my Dodge Nitro?
To diagnose a check engine light on your Dodge Nitro, first, use an OBD-II scanner to retrieve the trouble code. Research the code and identify the potential causes of the problem. Then, inspect the affected components and replace or repair them as necessary.
How do I flush the radiator in my Dodge Nitro?
To flush the radiator in your Dodge Nitro, first, allow the engine to cool completely. Then, remove the radiator cap and drain the coolant into a container. Refill the radiator with a radiator flush solution and run the engine for the recommended time. Drain the radiator again and refill it with fresh coolant.
How do I replace the air filter in my Dodge Nitro?
To replace the air filter in your Dodge Nitro, first, locate the air filter housing under the hood. Then, remove the cover and take out the old filter. Clean the housing and install a new filter. Finally, replace the cover and ensure that it is securely in place.
How do I replace the alternator in my Dodge Nitro?
To replace the alternator in your Dodge Nitro, first, disconnect the negative battery cable. Then, remove the serpentine belt and disconnect the wiring harness from the alternator. Remove the bolts that hold the alternator in place and lift it out of the vehicle. Install the new alternator and reconnect the wiring harness and serpentine belt.
How do I replace the battery in my Dodge Nitro?
To replace the battery in your Dodge Nitro, first, locate the battery under the hood. Then, remove the negative cable followed by the positive cable. Remove the battery hold-down clamp and lift the battery out of the vehicle. Install the new battery and reconnect the cables in the reverse order.
How do I replace the brake pads on my Dodge Nitro?
To replace the brake pads on your Dodge Nitro, first, remove the wheel and caliper by loosening the bolts that hold them in place. Then, remove the old brake pads and replace them with new ones. Finally, reattach the caliper and wheel and test the brakes to ensure they are working properly.
How do I replace the fuel filter in my Dodge Nitro?
To replace the fuel filter in your Dodge Nitro, first, locate the filter under the vehicle near the fuel tank. Then, disconnect the fuel lines from the filter and remove it from the bracket. Install the new filter in the bracket and reconnect the fuel lines.
How do I replace the headlights in my Dodge Nitro?
To replace the headlights in your Dodge Nitro, first, remove the retaining clips or screws that hold the headlight assembly in place. Then, pull the assembly forward and unplug the wiring connector. Remove the old headlight and replace it with a new one. Finally, reattach the assembly and wiring connector and test the headlights.
How do I replace the spark plugs in my Dodge Nitro?
To replace the spark plugs in your Dodge Nitro, first, locate the spark plug wires and remove them from the spark plugs. Then, use a spark plug socket to remove the old spark plugs. Install new spark plugs and reconnect the spark plug wires in the correct order.
How do I replace the thermostat in my Dodge Nitro?
To replace the thermostat in your Dodge Nitro, first, allow the engine to cool completely. Then, locate the thermostat housing and remove it using a wrench. Take out the old thermostat and install a new one. Reattach the housing and ensure that it is tightly secured.
How do I troubleshoot a starting problem in my Dodge Nitro?
To troubleshoot a starting problem in your Dodge Nitro, first, check the battery and ensure that it is fully charged. Then, check the starter motor and ignition switch for faults. Finally, inspect the fuel system and fuses for any issues that may be preventing the vehicle from starting.
What is a Dodge Nitro automotive repair manual?
A Dodge Nitro automotive repair manual is a guide that provides detailed instructions on how to repair and maintain a Dodge Nitro vehicle. It contains step-by-step instructions and illustrations to help users understand the repair process. The manual also includes information on troubleshooting common problems and identifying parts that may need replacement.
Get notified for new manuals?
We'll send you a quick email when a new Dodge Nitro manual is added.