Jaguar MK II Workshop Manuals and Repair Manuals

Every Manual available online - found by our community and shared for FREE. Enjoy!

Jaguar MK II

The Jaguar Mark 2 is a medium-sized saloon car built from late 1959 to 1967 by Jaguar in Coventry, England. Until the XJ, Jaguar's postwar saloons were usually denoted by Roman Numerals (e.g. Mark VII, Mark VIII) while the Mark 2 used Arabic Numerals, denoted on the rear of the car as "MK 2". Compared to the Mark 1, appearance of the car was transformed by an increase of 18% in cabin glass area greatly improving vision. The car was re-engineered above the waistline, slender front pillars allowed a wider windscreen and the rear window almost wrapped around to the enlarged side windows. 83,976 units were produced between 1959 and 1967.

Jaguar MK II FAQ's

How do I change a flat tire on my Jaguar MK II?

To change a flat tire on your Jaguar MK II, start by locating the spare tire, jack, and lug wrench. Loosen the lug nuts of the flat tire, but do not remove them yet. Use the jack to lift the vehicle off the ground, making sure to place it in a secure and stable position. Fully remove the lug nuts and take off the flat tire. Mount the spare tire onto the wheel hub and hand-tighten the lug nuts. Lower the vehicle with the jack and tighten the lug nuts with the lug wrench in a criss-cross pattern. Finally, check the tire pressure and adjust if necessary.

How do I change the oil in my Jaguar MK II?

To change the oil in your Jaguar MK II, start by removing the oil drain plug located underneath the engine. Allow the old oil to fully drain before replacing the drain plug. Then, locate the oil filter and remove it using an oil filter wrench. Remember to lubricate the rubber gasket of the new oil filter before screwing it on. Finally, refill the engine with the recommended amount and type of oil, and ensure the oil level is correct using the dipstick.

How do I check and top up the power steering fluid in my Jaguar MK II?

To check and top up the power steering fluid in your Jaguar MK II, start by locating the power steering fluid reservoir, which is generally near the engine. Remove the cap and check the fluid level using the dipstick attached to the cap or by observing the markings on the reservoir. If the level is below the recommended range, add the appropriate type of power steering fluid until it reaches the proper level. Be cautious not to overfill the reservoir, as this can cause damage to the system. Regularly checking and maintaining the power steering fluid level helps ensure smooth and responsive steering.

How do I check the tire pressure on my Jaguar MK II?

To check the tire pressure on your Jaguar MK II, start by locating the valve stem on each tire. Remove the valve cap and firmly press the tire pressure gauge onto the valve stem. The gauge will display the current pressure reading. Compare this reading to the recommended tire pressure mentioned in the owner's manual or on the sticker located on the driver's side door jamb. If the pressure is too low, add air until it reaches the correct level. If it is too high, release some air until it matches the recommended pressure.

How do I jump-start my Jaguar MK II?

If your Jaguar MK II's battery is dead and you need to jump-start it, start by locating the battery and identifying the positive (+) and negative (-) terminals. Connect the positive terminal of the dead battery to the positive terminal of the working battery using a red jumper cable. Then, connect the negative terminal of the working battery to a metal surface on the dead vehicle, away from the battery. Start the working vehicle and let it run for a few minutes, then try starting the dead vehicle. Once it starts, remove the jumper cables in the reverse order of connection.

How do I replace a headlight bulb on my Jaguar MK II?

To replace a headlight bulb on your Jaguar MK II, start by opening the hood and locating the rear of the headlight assembly. You may need to remove the dust cover or access panel to reach the bulb. Disconnect the electrical connector from the bulb and release any retaining clips or screws that secure the bulb in place. Carefully remove the old bulb and replace it with a new one, making sure not to touch the glass part of the bulb. Reconnect the electrical connector, secure the bulb using the retaining clips or screws, and reinstall any removed covers or panels.

How do I replace a windshield wiper blade on my Jaguar MK II?

To replace a windshield wiper blade on your Jaguar MK II, start by lifting the wiper arm away from the windshield. Locate the release tab or button on the wiper blade connector and press it to release the old blade. Slide the old blade off the wiper arm and dispose of it properly. Align the new wiper blade with the wiper arm and slide it onto the connector until it clicks into place. Gently lower the wiper arm back onto the windshield. Replace both wiper blades regularly for optimal visibility during inclement weather.

How do I replace the air filter in my Jaguar MK II?

To replace the air filter in your Jaguar MK II, start by locating the air filter housing, which is usually located near the engine. Open the housing by removing the retaining clips or screws. Take out the old air filter and clean the housing if necessary. Inspect the new air filter to ensure it is the correct size and type. Install the new filter, making sure it is properly seated and that the housing is securely closed. Regularly replacing the air filter helps maintain optimal engine performance and improves fuel efficiency.

How do I replace the brake pads on my Jaguar MK II?

To replace the brake pads on your Jaguar MK II, start by loosening the lug nuts of the wheel where you're changing the pads. Then, lift the vehicle using a jack and secure it with jack stands. Remove the wheel to access the brake caliper and locate the brake pad retaining pins or clips. Take note of their position before removing them and sliding out the old brake pads. Clean the caliper and install the new brake pads, making sure they are properly aligned. Finally, reinsert the retaining pins or clips, put the wheel back on, and tighten the lug nuts.

How do I replace the spark plugs in my Jaguar MK II?

To replace the spark plugs in your Jaguar MK II, start by locating the spark

How do I reset the maintenance light on my Jaguar MK II?

To reset the maintenance light on your Jaguar MK II, start by turning the ignition key to the "ON" position without starting the engine. Locate and press the "MENU" or "SETUP" button on the instrument cluster until you reach the maintenance menu. Use the arrow buttons to navigate to the "RESET" or "MAINTENANCE RESET" option and press the corresponding button to confirm. The maintenance light should now be reset. If the light persists or you encounter any issues, consult the owner's manual or contact a Jaguar dealership for further assistance.

How do I troubleshoot a malfunctioning power window in my Jaguar MK II?

If you are experiencing issues with a power window in your Jaguar MK II, start by checking the window fuse in the fuse box to ensure it is not blown. If the fuse is intact, try operating the window from both the driver's control panel and the individual door control panel to determine if the issue is isolated to a specific switch. Inspect the wiring and connections for any signs of damage or loose connections. If all else fails, it is recommended to consult the Jaguar MK II automotive repair manual for detailed troubleshooting steps or seek professional assistance.

How often should I change the transmission fluid in my Jaguar MK II?

It is generally recommended to change the transmission fluid in your Jaguar MK II every 30,000 to 60,000 miles, or as specified in the owner's manual. However, if you often drive in severe conditions such as stop-and-go traffic or towing heavy loads, it is advisable to change the transmission fluid more frequently to maintain optimal performance and extend the life of the transmission. Always use the recommended type and quantity of transmission fluid as indicated in the manual or by the manufacturer.

What type of coolant should I use in my Jaguar MK II?

It is recommended to use a high-quality, ethylene glycol-based coolant in your Jaguar MK II. This type of coolant offers excellent heat transfer properties and provides protection against freezing and overheating. Make sure to choose a coolant that meets the specifications outlined in the owner's manual or recommended by the manufacturer. Additionally, always mix the coolant with distilled water in the proper ratio before adding it to the cooling system.

What type of engine oil should I use in my Jaguar MK II?

It is important to use engine oil that meets the specifications mentioned in the owner's manual or recommended by the manufacturer. Generally, a high-quality synthetic or synthetic blend oil with the appropriate viscosity rating is recommended for optimum performance and protection. The recommended oil viscosity for your Jaguar MK II may vary based on factors such as climate and driving conditions, so it is crucial to follow the manufacturer's guidelines to ensure proper lubrication and engine longevity.