Mazda Tribute Workshop Manuals and Repair Manuals

Every Manual available online - found by our community and shared for FREE. Enjoy!

Mazda Tribute

The Mazda Tribute made its debut at the 2000 Los Angeles Auto Show as a compact crossover SUV, a segment pioneered by the Toyota RAV4 in 1994. Its conservative styling resembled and eventually somewhat replaced the Mazda Navajo, a rebadged two-door Ford Explorer which was retired in 1994. The 2001 2006 Mazda Tribute was available as front- or four-wheel drive and featured plain-looking but comfortable roomy interior, decent handling and car-like ride. It was offering front or all wheel drive and a choice of a transversely mounted 2.0 L Ford Zetec 4-cylinder engine with 129 PS or 3.0 L Ford Duratec V6 with 203 PS. Starting from 2006, Mazda stopped selling and producing Tribute in Japan, and replaced it with similar sized CX-7. In 2008 Mazda Australia also discontinued the Tribute.

Mazda Tribute FAQ's

How do I change the oil in a Mazda Tribute?

To change the oil in a Mazda Tribute, start by locating the oil drain plug underneath the vehicle. Use a wrench to loosen and remove the drain plug, allowing the old oil to drain out completely. Once drained, replace the drain plug and remove the oil filter. Install a new oil filter, then refill the engine with the recommended amount and type of oil.

How do I check the transmission fluid level in a Mazda Tribute?

To check the transmission fluid level in a Mazda Tribute, start the engine and allow it to warm up. Locate the transmission dipstick, which is usually labeled and located near the back of the engine bay. Remove the dipstick, wipe it clean, then reinsert it fully and remove it again. Check the fluid level on the dipstick, ensuring it falls within the recommended range indicated.

How do I diagnose a check engine light in a Mazda Tribute?

To diagnose a check engine light in a Mazda Tribute, start by using an OBD-II scanner to retrieve the trouble codes stored in the vehicle's computer. These codes can provide valuable information about the specific issue causing the check engine light to illuminate. Once the codes are obtained, refer to the repair manual for the corresponding diagnostic procedures and potential solutions for each code.

How do I replace a battery in a Mazda Tribute?

To replace a battery in a Mazda Tribute, start by turning off the engine and ensuring all electrical accessories are turned off. Locate the battery, which is typically located in the engine bay. Disconnect the negative (black) terminal first, followed by the positive (red) terminal. Remove any retaining hardware, then carefully lift out the old battery. Place the new battery in the same position, reconnect the terminals, and secure the battery in place.

How do I replace a cabin air filter in a Mazda Tribute?

To replace a cabin air filter in a Mazda Tribute, locate the cabin air filter housing, which is usually located behind the glove box or under the dashboard. Remove any covers or panels to access the housing. Open the housing and remove the old filter, noting its orientation. Insert the new filter in the correct position, close the housing, and reassemble any covers or panels that were removed.

How do I replace a fuel filter in a Mazda Tribute?

To replace a fuel filter in a Mazda Tribute, start by relieving fuel system pressure by removing the fuel pump fuse or relay and allowing the engine to run until it stalls. Locate the fuel filter, which is usually located along the fuel line underneath the vehicle. Use line wrenches to disconnect the fuel lines from the filter, then remove the mounting brackets or clips securing the filter. Install the new fuel filter in the reverse order, ensuring the fuel lines are properly connected and tightened.

How do I replace a headlight bulb in a Mazda Tribute?

To replace a headlight bulb in a Mazda Tribute, open the hood and locate the back of the headlight assembly. Disconnect the electrical connector from the bulb, then twist and remove the bulb from the socket. Insert the new bulb into the socket, making sure it is securely in place. Reconnect the electrical connector and test the headlight to ensure it is working properly.

How do I replace a serpentine belt in a Mazda Tribute?

To replace a serpentine belt in a Mazda Tribute, locate the belt tensioner, which is a spring-loaded pulley that keeps tension on the belt. Use a wrench or socket to rotate the tensioner and release tension on the belt. Remove the old belt from the pulleys, then route the new belt in the correct pattern around the pulleys. Rotate the tensioner again to allow the new belt to be installed, then release the tensioner to provide proper tension.

How do I replace a spark plug in a Mazda Tribute?

To replace a spark plug in a Mazda Tribute, start by locating the spark plug wires or ignition coils, which are usually connected to the top of the engine. Disconnect the wire or coil from the spark plug, then use a spark plug socket and ratchet to remove the old spark plug. Install the new spark plug, ensuring it is properly gapped, and tighten it to the manufacturer's specifications. Reconnect the wire or coil and repeat the process for each spark plug on the engine.

How do I replace the brake pads in a Mazda Tribute?

To replace the brake pads in a Mazda Tribute, start by safely lifting the vehicle and removing the wheel. Locate the brake caliper, which is usually secured with bolts or pins. Remove the caliper and then the old brake pads. Install the new brake pads, making sure they are positioned correctly, and reassemble the caliper. Repeat the process for each brake assembly on the vehicle.

How do I reset the maintenance light in a Mazda Tribute?

To reset the maintenance light in a Mazda Tribute, insert the key into the ignition and turn it to the "on" position without starting the engine. Press and hold the trip/reset button on the instrument panel until the maintenance light begins to flash. Continue holding the button until the light turns off, indicating that the reset is complete. Release the button and turn off the ignition.

How do I troubleshoot an electrical issue in a Mazda Tribute?

To troubleshoot an electrical issue in a Mazda Tribute, start by checking the fuses related to the affected circuits. Use a fuse tester or visually inspect the fuses to ensure they are not blown. If the fuses are intact, check for loose or corroded electrical connections, damaged wiring, or faulty components. Utilize the wiring diagrams and troubleshooting procedures in the repair manual to diagnose and resolve the specific electrical issue.

How often should I replace the air filter in a Mazda Tribute?

The air filter in a Mazda Tribute should generally be replaced every 12,000 to 15,000 miles or as recommended by the manufacturer. However, if you frequently drive in dusty or dirty conditions, it may be necessary to replace the air filter more frequently to ensure optimal engine performance. Regularly inspect the air filter for signs of dirt, debris, or damage, and replace it if necessary.

What is the recommended tire pressure for a Mazda Tribute?

The recommended tire pressure for a Mazda Tribute can usually be found in the owner's manual or on a sticker located on the driver's side door jamb. It is important to maintain the proper tire pressure as specified by the manufacturer, as it affects the vehicle's handling, fuel efficiency, and tire wear. Use a tire pressure gauge to check the pressure and adjust it accordingly.

What type of coolant should I use in a Mazda Tribute?

The recommended coolant for a Mazda Tribute is typically a mixture of ethylene glycol and water, also known as antifreeze. It is important to use the correct type of coolant as specified by the manufacturer, as different formulations can have varying effects on the engine's cooling system. Consult the owner's manual or check with a Mazda dealership to determine the specific coolant requirements for your vehicle.

Mazda Tribute Manuals Index

Mazda Tribute Workshop Manual

Mazda Tribute Owners Manual

Mazda Tribute Misc Document

Related Models