Mazda Xedos Workshop Manuals and Repair Manuals

Every Manual available online - found by our community and shared for FREE. Enjoy!

Mazda Xedos

The Mazda Xedos was a range of executive cars launched by Japanese manufacturer Mazda in 1992. The original model was the Mazda Xedos 6, which was similar in size and in engine to the BMW 3 Series. The Xedos 6 has 2 types of engines - 24 valve V6 @ 144 hp named KF and 16 valve L4 @ 107 hp named B6. In 1994, Xedos Mazda renewed the Xedos 6 model with changes in engine ecological standards and body exterior. The Xedos 6 was known as the Eunos 500 in Japan. This vehicle was not sold in the USA and Canada. The total quantity of Xedos 6 and Eunos 500 manufactured is 72101. Production ceased in 2000.

Mazda Xedos FAQ's

How do I bleed the brake system on a Mazda Xedos?

To bleed the brake system on a Mazda Xedos, start with the brake furthest away from the master cylinder, typically the rear passenger side. Have a helper press and hold the brake pedal while you open the bleeder valve to release any air or contaminants. Close the valve before releasing the brake pedal. Repeat this process for each brake, working your way towards the front of the vehicle, until all air is purged from the system. It is important to use the recommended brake fluid and follow proper safety procedures during the bleeding process.

How do I change the oil filter on a Mazda Xedos?

To change the oil filter on a Mazda Xedos, locate the oil filter housing, typically found near the engine. Use an oil filter wrench to loosen and remove the old filter. Before installing the new filter, apply a thin layer of oil on the rubber gasket to ensure a proper seal. Tighten the new filter by hand, being careful not to overtighten, and then refill the engine with the recommended amount of oil.

How do I check the transmission fluid level on a Mazda Xedos?

To check the transmission fluid level on a Mazda Xedos, start the engine and let it idle for a few minutes to warm up. Locate the transmission dipstick, usually found near the back of the engine compartment. Insert the dipstick, remove it, and check the fluid level. If the level is below the recommended range, add the appropriate transmission fluid until it reaches the proper level. Remember to use the specified type of fluid as mentioned in the owner's manual.

How do I replace a cabin air filter on a Mazda Xedos?

To replace a cabin air filter on a Mazda Xedos, locate the cabin air filter housing, which is usually located behind the glove compartment or under the dashboard. Open the housing, remove the old filter, and clean the housing if necessary. Install the new cabin air filter, ensuring it is properly aligned and secured. Finally, close the housing and test the air conditioning or ventilation system to check for proper airflow.

How do I replace a faulty ignition coil on a Mazda Xedos?

To replace a faulty ignition coil on a Mazda Xedos, locate the coil pack, which is usually located on top of the engine. Disconnect the electrical connector from the faulty coil, then remove the mounting bolts or screws that secure the coil in place. Carefully pull out the old coil and insert the new one, ensuring it is properly seated. Reattach the mounting bolts or screws, reconnect the electrical connector, and test the ignition system to verify proper operation.

How do I replace a faulty oxygen sensor on a Mazda Xedos?

To replace a faulty oxygen sensor on a Mazda Xedos, locate the sensor, which is typically threaded into the exhaust system. Disconnect the electrical connector from the sensor, then use an appropriate wrench or socket to remove the old sensor. Apply anti-seize compound to the threads of the new sensor and install it into the exhaust system. Reconnect the electrical connector, clear any stored error codes using a diagnostic tool, and test the vehicle to ensure the new oxygen sensor is functioning correctly.

How do I replace a headlight bulb on a Mazda Xedos?

To replace a headlight bulb on a Mazda Xedos, open the hood and locate the back of the headlight assembly. Disconnect the electrical connector from the bulb, then twist and remove the bulb holder or retainer. Take out the old bulb and insert the new one, making sure it is properly aligned. Reattach the bulb holder or retainer, reconnect the electrical connector, and test the headlight to ensure it is functioning correctly.

How do I replace a serpentine belt on a Mazda Xedos?

To replace a serpentine belt on a Mazda Xedos, locate the belt routing diagram, usually found under the hood or in the owner's manual. Use a wrench or tensioner tool to relieve tension on the belt, then carefully remove it from the pulleys. Install the new belt following the routing diagram, making sure it is properly seated on each pulley. Finally, release the tensioner to apply tension to the new belt and ensure it is properly aligned.

How do I reset the maintenance light on a Mazda Xedos?

To reset the maintenance light on a Mazda Xedos, turn the ignition key to the "ON" position without starting the engine. Press and hold the trip meter reset button until the maintenance light starts flashing or remains illuminated. Release the button and then turn the ignition key to the "OFF" position. Start the engine to verify if the maintenance light has been successfully reset.

How do I troubleshoot a faulty power window on my Mazda Xedos?

If you are experiencing issues with a power window on your Mazda Xedos, start by checking the fuse related to the power windows in the fuse box. If the fuse is intact, test the window switch by swapping it with a known working switch from another window. If the switch is not the problem, inspect the window motor and regulator for any signs of damage or malfunction. It may be necessary to replace the faulty component to resolve the power window issue.

How often should I replace the timing belt on my Mazda Xedos?

The timing belt on a Mazda Xedos should be replaced according to the manufacturer's recommended maintenance schedule, which is typically around 60,000 to 100,000 miles or about every 5 to 7 years. It is crucial to replace the timing belt within the specified interval to prevent potential engine damage if the belt were to fail. Regular inspection of the timing belt is also advisable to ensure it is in good condition and free from any signs of wear or damage.

What is the recommended tire pressure for a Mazda Xedos?

The recommended tire pressure for a Mazda Xedos can vary depending on the specific model and tire size. It is important to refer to the tire placard located on the driver's side door jamb or the owner's manual for the accurate tire pressure specifications. The recommended tire pressure is typically measured in pounds per square inch (psi) and should be checked regularly to ensure optimal tire performance, fuel efficiency, and safety.

What should I do if my Mazda Xedos is not starting?

If your Mazda Xedos is not starting, there are a few potential causes to consider. Check the battery to ensure it has enough charge and the connections are secure. Inspect the fuel system for any issues such as a clogged fuel filter or a faulty fuel pump. Additionally, it is advisable to check the ignition system for any faulty components, such as spark plugs or ignition coils. If the problem persists, it may be necessary to consult a professional mechanic.

What type of coolant should I use for my Mazda Xedos?

For the Mazda Xedos, it is recommended to use a long-life coolant that meets the specifications outlined in the owner's manual. Typically, this would be a coolant that is a mix of ethylene glycol and water, with the appropriate additives to prevent corrosion and maintain proper cooling properties. It is important to use the correct coolant to avoid any potential damage to the cooling system.

Mazda Xedos Manuals Index

Mazda Xedos Workshop Manual

Mazda Xedos Owners Manual

Related Models