Mercedes CE 300 Workshop Manuals and Repair Manuals
Every Manual available online - found by our community and shared for FREE. Enjoy!
Mercedes CE 300
The Coupe variant of the 124 Series was introduced at the Geneva Motor Show in 1987. The first models were the 230CE and 300CE. The 300 CE was built with 2962 ccm engine, 132kW (180hp), 5 speed manual transmission with 0-100 km/h acceleration in 7.9 seconds. Maximum speed of 300CE was 225 km/h. Stylistically the Coupes of the 124 series display their affinity to the Saloon, presenting themselves with the same composed, clear lines for which chief designer Bruno Sacco was responsible. And yet their looks make them cars in their own right: the Coupés are a little shorter than the corresponding Saloons, are designed as two-doors, and their windscreen and rear window have a flatter angle. These stylistic features emphasize the character of these exclusive vehicles.Mercedes CE 300 FAQ's
How can I check the tire pressure in my Mercedes CE 300?
To check the tire pressure in your Mercedes CE 300, locate the tire pressure monitoring system (TPMS) button inside the vehicle or refer to the owner's manual for its exact location. With the vehicle turned on, press and hold the TPMS button until the tire pressure readings appear on the instrument cluster. Compare the displayed readings with the recommended tire pressure specifications to determine if any adjustments are necessary.
How can I diagnose a misfiring engine in my Mercedes CE 300?
If you suspect a misfiring engine in your Mercedes CE 300, start by checking for any stored trouble codes using a diagnostic scanner. These codes can provide valuable insight into the specific cylinder(s) experiencing the misfire. Additionally, inspect the spark plugs, ignition coils, and fuel injectors for any signs of damage or wear. If the issue persists, it may be necessary to perform a compression test and further diagnostic procedures to pinpoint the underlying cause of the misfire.
How can I troubleshoot a malfunctioning power window in my Mercedes CE 300?
If you are experiencing a malfunctioning power window in your Mercedes CE 300, start by checking the fuse associated with the power window circuit. If the fuse is intact, try operating the window from both the driver's control panel and the individual door control switch. If the window still does not respond, it may indicate a faulty window motor or regulator, which would require further inspection and potentially replacement.
How do I change the oil in my Mercedes CE 300?
To change the oil in your Mercedes CE 300, begin by locating the oil drain plug underneath the vehicle. Use a wrench to remove the drain plug and allow the old oil to drain completely. Once drained, replace the drain plug and refill the engine with the recommended amount and type of oil specified in the owner's manual.
How do I check the brake fluid level in my Mercedes CE 300?
To check the brake fluid level in your Mercedes CE 300, locate the brake fluid reservoir under the hood. The reservoir is typically transparent, allowing you to visually inspect the fluid level. Ensure the vehicle is on a level surface and that the reservoir cap is clean before removing it. The brake fluid level should be between the minimum and maximum marks on the reservoir. If necessary, add the recommended brake fluid specified in the owner's manual.
How do I properly jump-start my Mercedes CE 300?
To properly jump-start your Mercedes CE 300, begin by positioning both vehicles close enough for the jumper cables to reach each battery. Turn off both vehicles' ignitions and connect the positive (red) jumper cable to the positive terminal of the dead battery, then connect the other end to the positive terminal of the assisting vehicle's battery. Next, connect the negative (black) jumper cable to the negative terminal of the assisting vehicle's battery, followed by connecting the other end to an unpainted metal surface on the engine block of the dead vehicle. Start the assisting vehicle and let it run for a few minutes, then attempt to start the dead vehicle. Once started, remove the jumper cables in the reverse order they were connected.
How do I replace a burnt-out headlight bulb in my Mercedes CE 300?
To replace a burnt-out headlight bulb in your Mercedes CE 300, locate the headlight assembly behind the respective headlight lens. Disconnect the electrical connector from the back of the bulb and remove the retaining clip or cover. Carefully remove the old bulb and install the new one, ensuring it is properly aligned and secured before reconnecting the electrical connector.
How do I replace a faulty fuel pump in my Mercedes CE 300?
Replacing a faulty fuel pump in your Mercedes CE 300 typically requires accessing the fuel tank. Begin by disconnecting the negative battery cable and relieving the fuel system pressure. Remove any necessary components or shielding obstructing access to the fuel tank. Disconnect the fuel lines and electrical connectors from the fuel pump assembly. Remove the retaining ring or bolts securing the pump assembly and carefully lift it out of the tank. Install the new fuel pump following the reverse procedure and ensure all connections are properly secured before reassembling other components.
How do I replace a faulty spark plug in my Mercedes CE 300?
To replace a faulty spark plug in your Mercedes CE 300, begin by identifying the location of the spark plug on the engine. Disconnect the electrical connector and remove any necessary components obstructing access to the spark plug. Use a spark plug socket and ratchet to remove the old spark plug and install the new one, ensuring proper torque specifications are followed. Reconnect the electrical connector and any components that were removed.
How do I replace a malfunctioning oxygen sensor in my Mercedes CE 300?
To replace a malfunctioning oxygen sensor in your Mercedes CE 300, locate the sensor(s) on the exhaust system. Disconnect the electrical connector and use an appropriate oxygen sensor socket to remove the old sensor. Apply anti-seize compound to the threads of the new sensor and install it in the same location, ensuring it is tightened to the specified torque. Reconnect the electrical connector and clear any stored trouble codes using a diagnostic scanner.
How do I replace a worn-out serpentine belt in my Mercedes CE 300?
To replace a worn-out serpentine belt in your Mercedes CE 300, begin by locating the belt tensioner, usually found near the front of the engine. Use a wrench or socket to rotate the tensioner in the direction specified in the owner's manual, relieving tension on the belt. Carefully remove the old belt from the pulleys and route the new belt following the appropriate diagram. Rotate the tensioner again, allowing the new belt to be installed on the pulleys. Double-check the belt's alignment and tension before starting the engine.
How do I reset the service indicator on my Mercedes CE 300?
To reset the service indicator on your Mercedes CE 300, turn the ignition to position 1 (without starting the engine). Press and hold the reset button, usually located on the instrument cluster, until the message "Resetting Service Indicator" appears. Release the reset button and turn off the ignition. When you start the engine again, the service indicator should be reset.
How often should I replace the air filter in my Mercedes CE 300?
It is generally recommended to replace the air filter in your Mercedes CE 300 every 15,000 to 30,000 miles or as specified in the owner's manual. However, this interval may vary depending on driving conditions and the environment in which the vehicle operates. Regularly inspecting the air filter for excessive dirt or debris accumulation is also advisable.
What is the recommended maintenance schedule for my Mercedes CE 300?
The recommended maintenance schedule for your Mercedes CE 300 can be found in the owner's manual. It outlines various maintenance tasks, such as oil changes, filter replacements, fluid checks, and inspections, along with their corresponding intervals. Adhering to this schedule helps ensure the longevity and optimal performance of your vehicle.
What type of coolant should I use in my Mercedes CE 300?
It is recommended to use a high-quality, ethylene glycol-based coolant that meets the specifications outlined in the owner's manual. These specifications ensure proper performance and protection for your Mercedes CE 300's cooling system. It's important to avoid using tap water or mixing different coolant types, as this can lead to potential damage or decreased cooling efficiency.
Mercedes CE 300 on Amazon
Mercedes CE 300 Owners Manual
-
- Mercedes CE 300 Owners Manual
- (140 Pages)
- (Free)
Related Models