Mitsubishi 3000 GT Workshop Manuals and Repair Manuals
Every Manual available online - found by our community and shared for FREE. Enjoy!
Mitsubishi 3000 GT
The Mitsubishi 3000 GT is a sports car manufactured in Japan by Mitsubishi Motors. The car goes by different names in markets outside Japan. The first generation model incorporated many of Mitsubishi's contemporary performance-enhancing technologies, such as full-time four-wheel drive, four-wheel steering, active aerodynamics featuring automatically adjusting front and rear spoilers, sport/tour exhaust modes and electronically controlled suspension (ECS). In the international market, the sports car is also called Mitsubishi GTO. The 1991 to 1996 models were slightly modified by Chrysler Company for the American market, and the modified version was named Dodge Stealth. The car largely borrows its name from the Galant GTO.Mitsubishi 3000 GT FAQ's
How do I change a flat tire on a Mitsubishi 3000 GT?
If you experience a flat tire in a Mitsubishi 3000 GT, first find a safe location to pull over and engage the parking brake. Locate the spare tire, jack, and lug wrench in the trunk or under the vehicle. Use the lug wrench to loosen the lug nuts on the flat tire, then use the jack to lift the vehicle off the ground. Remove the lug nuts and the flat tire, then install the spare tire and tighten the lug nuts. Lower the vehicle, tighten the lug nuts further, and double-check their tightness before driving.
How do I change the oil in a Mitsubishi 3000 GT?
To change the oil in a Mitsubishi 3000 GT, start by locating the oil drain plug underneath the engine. Remove the plug and drain the old oil into a suitable container. Once the oil has completely drained, replace the drain plug and remove the oil filter. Install a new filter and then refill the engine with the recommended amount and type of oil, as specified in the owner's manual.
How do I flush the coolant in a Mitsubishi 3000 GT?
To flush the coolant in a Mitsubishi 3000 GT, start by ensuring the engine is cool. Locate the radiator drain plug at the bottom of the radiator and place a suitable container beneath it to catch the coolant. Remove the drain plug and allow the coolant to completely drain. Once drained, close the drain plug and refill the system with a mixture of coolant and distilled water as specified in the owner's manual. Bleed any air from the system, then start the engine and check for any leaks or further coolant adjustments.
How do I replace a headlight bulb in a Mitsubishi 3000 GT?
To replace a headlight bulb in a Mitsubishi 3000 GT, open the hood and locate the back of the headlight assembly. Unplug the electrical connector from the bulb and remove the rubber cover if present. Depending on the type of headlight assembly, either twist the bulb socket counterclockwise or release the retaining clip to remove the bulb. Install the new bulb, ensuring it is properly aligned, and secure it in place. Reconnect the electrical connector and test the headlight before closing the hood.
How do I replace the air filter in a Mitsubishi 3000 GT?
To replace the air filter in a Mitsubishi 3000 GT, start by locating the air filter housing, which is usually near the engine's intake. Open the housing by removing the clips or screws that secure it. Take out the old air filter and clean any debris in the housing. Install a new air filter, ensuring it is properly seated. Finally, secure the air filter housing and ensure it is tightly closed.
How do I replace the battery in a Mitsubishi 3000 GT?
To replace the battery in a Mitsubishi 3000 GT, start by turning off the engine and removing the key from the ignition. Locate the battery in the engine bay and carefully disconnect the negative (-) cable followed by the positive (+) cable. Remove any brackets or hold-downs securing the battery in place. Lift the old battery out and install the new one, ensuring proper polarity. Reconnect the positive (+) cable followed by the negative (-) cable. Finally, start the vehicle to confirm that the new battery is functioning correctly.
How do I replace the brake pads in a Mitsubishi 3000 GT?
To replace the brake pads in a Mitsubishi 3000 GT, start by lifting the vehicle and securely supporting it on jack stands. Remove the wheels to gain access to the brake calipers. Use a suitable tool to compress the caliper pistons and remove the caliper bolts. Take out the old brake pads and replace them with new ones. Reinstall the caliper, tighten the bolts, and repeat the process for the remaining wheels.
How do I replace the serpentine belt in a Mitsubishi 3000 GT?
To replace the serpentine belt in a Mitsubishi 3000 GT, start by locating the belt routing diagram, usually found on a sticker or in the owner's manual. Release the tension on the belt by using a suitable tool on the tensioner pulley. Once the tension is relieved, slip the belt off the pulleys. Install the new belt following the belt routing diagram. Apply tension to the belt using the tensioner pulley, ensuring it is properly seated on all pulleys. Check the belt for proper alignment and tension before starting the engine.
How do I replace the spark plugs in a Mitsubishi 3000 GT?
To replace the spark plugs in a Mitsubishi 3000 GT, start by disconnecting the negative (-) battery cable. Locate the spark plugs, usually on top of the engine cylinder head. Remove the spark plug wires or ignition coil packs to access the spark plugs. Use a spark plug socket and a ratchet to remove the old spark plugs. Install new spark plugs, ensuring they are properly gapped, and tighten them to the recommended torque. Reinstall the spark plug wires or ignition coil packs and reconnect the negative (-) battery cable.
How do I reset the maintenance light in a Mitsubishi 3000 GT?
To reset the maintenance light in a Mitsubishi 3000 GT, start by turning the ignition switch to the "ON" position without starting the engine. Press and hold the trip/reset button on the instrument cluster until the maintenance light starts flashing. Release the button and then press and hold it again until the light goes out. Turn off the ignition, and when you start the vehicle again, the maintenance light should be reset.
How do I troubleshoot a non-starting Mitsubishi 3000 GT?
If a Mitsubishi 3000 GT fails to start, there are several potential causes to consider. First, check the battery voltage and ensure it is fully charged. Check the connections to the battery terminals and ensure they are tight and free of corrosion. If the battery is fine, check the starter motor and solenoid for any issues. Inspect the ignition switch, fuses, and relays related to the starting system. If all these components are in good condition, it is advisable to seek the assistance of a professional mechanic for further diagnostic steps.
How often should I replace the timing belt in a Mitsubishi 3000 GT?
The timing belt in a Mitsubishi 3000 GT should be replaced every 60,000 to 90,000 miles or every 5 to 7 years, whichever comes first. It is crucial to replace the timing belt within the recommended interval to prevent potential engine damage. Neglecting to replace the timing belt can result in belt failure, causing severe engine problems and costly repairs.
What should I do if my Mitsubishi 3000 GT overheats?
If your Mitsubishi 3000 GT starts to overheat, the first thing to do is pull over to a safe location and turn off the engine. Allow the engine to cool down before attempting any further action. Check the coolant level and ensure it is at the recommended level. If the coolant level is low, add coolant and check for any leaks. If the coolant level is fine, there might be an issue with the radiator, thermostat, or water pump, and it is advisable to consult a professional mechanic.
What should I do if my Mitsubishi 3000 GT's check engine light comes on?
When the check engine light illuminates in a Mitsubishi 3000 GT, it indicates that there is a problem with the engine or emission control system. It is important to have the vehicle diagnosed by a qualified mechanic or use an OBD-II scanner to retrieve the error codes. These codes can provide valuable information about the specific issue causing the check engine light to come on. Once the problem is identified, appropriate repairs can be made to resolve the issue.
What type of transmission fluid should I use in a Mitsubishi 3000 GT?
The type of transmission fluid recommended for a Mitsubishi 3000 GT depends on the model year and transmission type. Consult the owner's manual or the Mitsubishi 3000 GT automotive repair manual for the exact specifications. Generally, Mitsubishi recommends using a high-quality ATF (Automatic Transmission Fluid) such as Mitsubishi Diamond ATF SP III or an equivalent fluid that meets the specified requirements.
Mitsubishi 3000 GT Manuals Index
Mitsubishi 3000 GT Workshop Manual
- (Free)
-
- Mitsubishi 3000 GT 1991 Workshop Manual Volume I
- (1,146 Pages)
- (Free)
- (Free)
-
- Mitsubishi 3000 GT 1992 1996 Workshop Manual Volume I
- (1,308 Pages)
- (Free)
- (Free)
- (Free)
- (Free)
- (Free)
-
- Mitsubishi 3000 GT 1997 Workshop Manual 3.0L DOHC MFI
- (8,375 Pages)
- (Free)
-
- Mitsubishi 3000 GT 1997 Workshop Manual SL V6 3.0L DOHC
- (8,375 Pages)
- (Free)
-
- Mitsubishi 3000 GT 1998 Workshop Manual V6 3.0L SOHC
- (7,841 Pages)
- (Free)
-
- Mitsubishi 3000 GT Workshop Manual Back Up
- (522 Pages)
- (Free)
-
- Mitsubishi 3000 GT Workshop Manual BRM
- (148 Pages)
- (Free)
-
- Mitsubishi 3000GT 1998 Workshop Manual 3.0L DOHC MFI
- (7,513 Pages)
- (Free)
Mitsubishi 3000 GT Misc Document
- (Free)
- (Free)
Related Models