Mitsubishi Lancer Evolution Workshop Manuals and Repair Manuals

To change the headlights in your Mitsubishi Lancer Evolution, open the hood and locate the back of the headlight assembly. Disconnect the electrical connector, remove the retaining clips or screws, and carefully pull out the old bulb. Install the new bulb, ensuring it is securely in place, and reattach the electrical connector and retaining clips.

To check the brake fluid level in your Mitsubishi Lancer Evolution, locate the brake fluid reservoir under the hood. The reservoir is usually translucent and marked with high and low level indicators. Ensure the vehicle is on a level surface, remove the cap, and visually inspect the fluid level. If necessary, add the recommended brake fluid type to bring it to the appropriate level.

To check the coolant level in your Mitsubishi Lancer Evolution, ensure the engine is cool and the vehicle is on a level surface. Locate the coolant reservoir under the hood, typically marked with high and low level indicators. Visually inspect the coolant level and add the appropriate coolant mixture if needed. Avoid opening the radiator cap when the engine is hot to prevent injury.

To check the tire pressure in your Mitsubishi Lancer Evolution, first, ensure the tires are cold. Locate the recommended tire pressure values on the driver's side door jamb or in the owner's manual. Use a tire pressure gauge to measure the pressure, and adjust if necessary. Proper tire pressure improves safety, handling, and fuel efficiency.

To check the transmission fluid level in your Mitsubishi Lancer Evolution, start the engine and allow it to reach operating temperature. Park the vehicle on a level surface, engage the parking brake, and shift through all gears before returning to Park. Locate the transmission dipstick, usually near the back of the engine bay, and remove it. Wipe the dipstick clean, reinsert it fully, then remove it again and check the fluid level. Add the recommended transmission fluid if necessary, following the owner's manual guidelines.

To jump-start your Mitsubishi Lancer Evolution, you will need a set of jumper cables and another vehicle with a fully charged battery. Connect the positive (red) cable to the positive terminal of the dead battery, then connect the other end to the positive terminal of the working battery. Connect the negative (black) cable to the negative terminal of the working battery, then attach the other end to a metal, unpainted part of the engine block on the dead vehicle. Start the engine of the working vehicle, let it run for a few minutes, then try starting the dead vehicle. Once started, remove the jumper cables in the reverse order of connection.

To replace the battery in your Mitsubishi Lancer Evolution, start by turning off the engine and all electrical components. Locate the battery in the engine bay, disconnect the negative (black) cable first, followed by the positive (red) cable. Remove any battery hold-down brackets or clamps, then carefully lift out the old battery. Install the new battery, ensuring the positive and negative terminals are connected correctly, and secure it with the hold-down brackets or clamps. Reconnect the positive cable first, followed by the negative cable, and ensure they are tightened securely.

To replace the serpentine belt in your Mitsubishi Lancer Evolution, locate the belt routing diagram under the hood. Use a wrench or belt tensioner tool to relieve tension on the belt, then carefully remove it from the pulleys. Compare the old belt to the new one to ensure the correct length and routing. Install the new belt following the correct path, ensuring it is properly seated on each pulley.

To replace the windshield wiper blades on your Mitsubishi Lancer Evolution, lift the wiper arm away from the windshield until it locks in the raised position. Locate the release tab or button on the wiper blade assembly and press it to release the old blade. Slide the new blade into place until it clicks, and gently lower the wiper arm back onto the windshield.

To reset the maintenance required light in your Mitsubishi Lancer Evolution, turn the ignition switch to the ON position without starting the engine. Fully press the accelerator pedal three times within 10 seconds. The maintenance required light should flash and then turn off, indicating that the reset was successful.

It is recommended to change the engine oil in your Mitsubishi Lancer Evolution every 5,000 miles or every six months, whichever comes first. Regular oil changes help maintain engine performance and prevent premature wear and tear. Be sure to use the recommended oil viscosity and quality specified in the owner's manual.

The air filter in your Mitsubishi Lancer Evolution should be replaced every 15,000 to 30,000 miles, depending on driving conditions. Regularly inspect the air filter for dirt and debris accumulation, and replace it if necessary. A clogged air filter can restrict airflow to the engine, reducing performance and fuel efficiency.

The cabin air filter in your Mitsubishi Lancer Evolution should be replaced every 15,000 to 30,000 miles, depending on driving conditions and air quality. A dirty or clogged cabin air filter can reduce the effectiveness of the HVAC system and result in poor air quality inside the vehicle. Refer to the owner's manual for the exact replacement interval and procedure.

The spark plugs in your Mitsubishi Lancer Evolution should be replaced every 30,000 to 45,000 miles, depending on driving conditions. Worn or fouled spark plugs can cause misfires, reduced power, and decreased fuel efficiency. Follow the manufacturer's recommendations and use the correct spark plug type and gap specified for your vehicle.

It is important to use premium unleaded gasoline with an octane rating of 91 or higher in your Mitsubishi Lancer Evolution. Using lower octane fuel can result in engine knocking and reduced performance. Additionally, avoid using ethanol-blended fuels exceeding 10% ethanol content, as they may negatively affect engine operation and fuel efficiency.