Mitsubishi Tredia Workshop Manuals and Repair Manuals
Every Manual available online - found by our community and shared for FREE. Enjoy!
Mitsubishi Tredia
The Mitsubishi Tredia was a subcompact sedan built by Mitsubishi Motors from 1982 to 1990. The Cordia and Tredia used front-wheel drive and were similar in design to the contemporary Mirage (although larger). They incorporated a MacPherson strut/beam axle suspension, front disc brakes, manual or electrically controlled automatic transmission, and a choice of three engines: a 1.4 litre rated at 68 hp, a 74 hp (55 kW) a 1.6 litre, and a 112 hp (84 kW) turbocharged 1.6 litre. Some export markets also received a carb-fed 110 hp (82 kW) 2.0 litre. A USA version of the 2.0 litre generated 88hp for the 1984 model year. The cars received a mild facelift in 1983, and four-wheel drive was offered in 1984.Mitsubishi Tredia FAQ's
How do I change the oil in a Mitsubishi Tredia?
To change the oil in a Mitsubishi Tredia, first locate the oil drain plug underneath the engine. Use a wrench to loosen and remove the drain plug, allowing the old oil to drain into a suitable container. After the oil has fully drained, replace the drain plug and remove the oil filter, which is typically located near the engine. Install a new oil filter and refill the engine with the recommended amount and type of oil, using a funnel if necessary.
How do I check and adjust the tire pressure in my Mitsubishi Tredia?
To check and adjust the tire pressure in a Mitsubishi Tredia, start by locating the tire pressure specifications, which are usually listed on a sticker inside the driver's side door jamb or in the owner's manual. Using a tire pressure gauge, measure the air pressure in each tire, including the spare tire if applicable. If the tire pressure is below the recommended level, add air using an air compressor or at a gas station. If the pressure is too high, release air until it reaches the recommended level. Regularly checking and maintaining proper tire pressure can enhance vehicle safety and fuel efficiency.
How do I diagnose and fix an electrical issue in my Mitsubishi Tredia?
If you are experiencing electrical issues in your Mitsubishi Tredia, there are a few steps you can take to diagnose and potentially fix the problem. Start by checking the vehicle's fuses and relays, ensuring they are properly seated and not blown. Inspect the battery terminals and connections for any corrosion or loose connections, cleaning or tightening as necessary. If the issue persists, consider using a multimeter to test various electrical components and circuits for continuity, voltage, or resistance. If you are unable to identify or fix the issue, it is recommended to consult a professional mechanic or refer to a Mitsubishi Tredia repair manual for further diagnosis and repair procedures.
How do I diagnose and repair a braking issue in my Mitsubishi Tredia?
If you are experiencing braking issues with your Mitsubishi Tredia, there are several potential causes to consider. Start by checking the brake fluid level and condition, topping it off or replacing it if necessary. Inspect the brake pads and rotors for any signs of wear or damage, and replace them if needed. Additionally, check the brake lines, calipers, and master cylinder for any leaks or malfunctions. If the issue persists, it is recommended to consult a professional mechanic or refer to a Mitsubishi Tredia repair manual for further diagnosis and repair procedures.
How do I replace a broken headlight in a Mitsubishi Tredia?
To replace a broken headlight in a Mitsubishi Tredia, open the hood and locate the headlight housing. Disconnect the electrical connector from the back of the headlight bulb and remove any retaining clips or screws holding the bulb in place. Carefully remove the old bulb and replace it with a new one, making sure it is securely seated. Reattach any retaining clips or screws, reconnect the electrical connector, and test the new headlight to ensure proper functioning.
How do I replace a faulty fuel pump in a Mitsubishi Tredia?
To replace a faulty fuel pump in a Mitsubishi Tredia, start by safely relieving the fuel system pressure by disconnecting the fuel pump fuse or relay and running the engine until it stalls. Then, disconnect the negative battery cable and locate the fuel pump, which is typically located inside the fuel tank. Remove the fuel tank if necessary to access the fuel pump assembly. Disconnect the electrical connectors and fuel lines connected to the pump, and carefully remove the pump from the tank. Install the new fuel pump, reconnect all components, and ensure proper functionality before reconnecting the battery cable.
How do I replace a faulty oxygen sensor in a Mitsubishi Tredia?
To replace a faulty oxygen sensor in a Mitsubishi Tredia, start by locating the sensor, typically mounted in the exhaust system. Disconnect the electrical connector attached to the sensor and use an oxygen sensor socket or a wrench to carefully remove the old sensor. Apply anti-seize compound to the threads of the new oxygen sensor, and install it in the correct position, ensuring proper alignment and tightening. Reconnect the electrical connector, and clear any diagnostic trouble codes using an OBD-II scanner. Finally, verify that the new oxygen sensor is functioning correctly by conducting a test drive or monitoring the sensor readings with an appropriate scan tool.
How do I replace a malfunctioning starter motor in a Mitsubishi Tredia?
To replace a malfunctioning starter motor in a Mitsubishi Tredia, start by disconnecting the negative battery cable for safety. Locate the starter motor, typically near the engine block, and remove any electrical connectors and mounting bolts attached to it. Carefully remove the old starter motor from its position, taking note of the orientation and location of any shims or spacers. Install the new starter motor in the correct position, ensuring that any shims or spacers are properly aligned. Reconnect the electrical connectors and mounting bolts, and reconnect the negative battery cable before testing the new starter motor.
How do I replace a worn-out serpentine belt in a Mitsubishi Tredia?
To replace a worn-out serpentine belt in a Mitsubishi Tredia, start by locating the belt tensioner, which is typically a pulley that applies tension to the belt. Use a wrench or a serpentine belt tool to rotate the tensioner and relieve tension on the belt. Then, carefully remove the old belt from the pulleys, making note of the belt routing to ensure proper installation of the new belt. Install the new belt by following the correct routing pattern, and rotate the tensioner again to allow the belt to slide onto the pulleys. Finally, release the tensioner to apply proper tension to the new belt.
How do I troubleshoot a faulty ignition system in my Mitsubishi Tredia?
If you are experiencing issues with your Mitsubishi Tredia's ignition system, there are a few steps you can take to troubleshoot the problem. First, check the battery connection and ensure it is clean and tightly secured. Next, inspect the spark plugs and ignition coils for any signs of damage or wear. If necessary, replace any faulty components. Additionally, check the ignition switch and ignition module for proper functionality. If the issue persists, it is advisable to consult a professional mechanic or refer to a Mitsubishi Tredia repair manual for further diagnosis and repair procedures.
How do I troubleshoot a malfunctioning air conditioning system in my Mitsubishi Tredia?
If your Mitsubishi Tredia's air conditioning system is not functioning properly, there are a few steps you can take to troubleshoot the issue. Start by checking the system's refrigerant level and ensuring it is within the recommended range. Inspect the
How often should I change the air filter in my Mitsubishi Tredia?
The air filter in a Mitsubishi Tredia should typically be replaced every 12,000 to 15,000 miles or as recommended by the vehicle manufacturer. However, this interval may vary depending on driving conditions and environment. Signs that your air filter may need replacement include reduced engine performance, decreased fuel efficiency, or a dirty and clogged appearance. Regularly inspect the air filter and replace it as needed to ensure optimal engine performance and air intake.
What should I do if my Mitsubishi Tredia's engine overheats?
If your Mitsubishi Tredia's engine starts to overheat, immediately turn off the vehicle and wait for it to cool down before attempting any further action. Check the coolant level in the radiator and reservoir tank, and if it is low, add coolant to the appropriate level. Inspect the radiator for any blockages or damage, and clean or repair as necessary. Additionally, check the radiator fan operation and ensure it is functioning properly. If the issue persists, it is recommended to consult a professional mechanic for further diagnosis and repair.
What type of coolant should I use in my Mitsubishi Tredia?
Mitsubishi Tredia vehicles typically require a specific type of coolant known as ethylene glycol-based coolant. It is important to use the correct coolant recommended by the manufacturer, as different types may have different chemical compositions and properties that can affect cooling system performance. Refer to the vehicle's owner's manual or consult a Mitsubishi Tredia repair manual for the exact coolant specifications and any additional guidelines or recommendations for coolant usage.
Mitsubishi Tredia on Amazon
Mitsubishi Tredia Workshop Manual
- (Free)
Related Models
