Nissan Prairie Workshop Manuals and Repair Manuals

Every Manual available online - found by our community and shared for FREE. Enjoy!

Nissan Prairie

The Nissan Prairie, introduced in Japan in 1981 and Europe in 1982, was a car from Japanese manufacturer Nissan. It was also known as the Multi in Canada and the Stanza Wagon in the United States. It was equipped with a 4 cylinder engine, with either a manual or automatic transmission. Available with front wheel drive or optional four wheel drive, the vehicle had rear passenger sliding doors on both sides of the vehicle, and a folding rear seat, designed to increase the carrying capacity of the passenger compartment. It was originally launched in Japan with a 1.5 L I4 engine mated to a 5 speed gearbox, followed shortly after by a 1.8 L and a 2.0 L engine (certain markets only).

Nissan Prairie FAQ's

How do I change the oil in a Nissan Prairie?

To change the oil in a Nissan Prairie, start by locating the oil drain plug underneath the engine. Use a wrench to loosen and remove the plug, allowing the old oil to drain into a suitable container. Once all the oil has drained, replace the drain plug and remove the old oil filter. Install a new oil filter and refill the engine with the recommended amount and type of oil, as specified in the Nissan Prairie automotive repair manual.

How do I change the spark plugs in a Nissan Prairie?

Changing the spark plugs in a Nissan Prairie involves locating the spark plug wires or ignition coils, depending on the specific engine configuration. Disconnect the wires or coils, and using a spark plug socket and ratchet, remove the old spark plugs. Inspect the plugs for signs of wear or damage, then gap the new spark plugs to the recommended specifications. Carefully install the new plugs, ensuring they are tightened to the proper torque. Reconnect the spark plug wires or ignition coils as per the instructions in the Nissan Prairie automotive repair manual.

How do I check the transmission fluid in a Nissan Prairie?

Checking the transmission fluid in a Nissan Prairie involves starting the engine and allowing it to reach operating temperature. Park the vehicle on a level surface and apply the parking brake. Locate the transmission dipstick, usually located near the back of the engine bay. Remove the dipstick, wipe it clean, and reinsert it fully. Remove the dipstick again and check the fluid level against the markings on the dipstick. If necessary, add the recommended type and amount of transmission fluid as specified in the Nissan Prairie automotive repair manual.

How do I flush and refill the cooling system in a Nissan Prairie?

Flushing and refilling the cooling system in a Nissan Prairie involves draining the old coolant, flushing the system with clean water, and refilling it with a proper coolant mixture. Start by opening the radiator drain plug or petcock to drain the coolant into a suitable container. Close the drain plug and flush the system by filling it with water and running the engine for a few minutes. Drain the water, then refill the system with the recommended coolant mixture. Bleed any air from the system as instructed in the Nissan Prairie automotive repair manual.

How do I replace a broken side mirror on a Nissan Prairie?

To replace a broken side mirror on a Nissan Prairie, first, remove the interior door panel to access the mirror mounting bolts. Disconnect any electrical connectors if applicable. Remove the bolts holding the mirror in place and carefully detach the mirror from the exterior of the door. Install the new mirror by reversing the steps, ensuring it is properly aligned and secured. Finally, reattach the interior door panel, following the instructions provided in the Nissan Prairie automotive repair manual.

How do I replace a faulty ignition coil in a Nissan Prairie?

To replace a faulty ignition coil in a Nissan Prairie, start by locating the ignition coil or coil pack, depending on the specific engine configuration. Disconnect the electrical connector(s) and remove any retaining bolts or screws holding the coil in place. Carefully lift out the old coil and install the new one, ensuring it is properly seated and secured. Reconnect the electrical connector(s) and verify that the coil is functioning correctly. Detailed instructions, including the specific ignition coil locations, can be found in the Nissan Prairie automotive repair manual.

How do I replace a faulty oxygen sensor in a Nissan Prairie?

To replace a faulty oxygen sensor in a Nissan Prairie, first, locate the sensor(s) in the exhaust system. Disconnect the electrical connector and use an oxygen sensor socket and ratchet to remove the old sensor. Install the new sensor, making sure to apply anti-seize compound to the threads if specified by the manufacturer. Reconnect the electrical connector and verify proper sensor operation. The Nissan Prairie automotive repair manual provides detailed instructions, including sensor locations and specifications, for a successful replacement process.

How do I replace a headlight bulb in a Nissan Prairie?

To replace a headlight bulb in a Nissan Prairie, first, locate the headlight assembly behind the respective lens cover. Disconnect the electrical connector and remove the retaining screws or clips holding the assembly in place. Carefully remove the assembly and access the bulb socket at the back. Twist and remove the old bulb, then insert the new bulb, ensuring it is properly aligned. Reassemble the headlight assembly and reconnect the electrical connector, following the instructions outlined in the Nissan Prairie automotive repair manual.

How do I replace a worn-out drive belt in a Nissan Prairie?

To replace a worn-out drive belt in a Nissan Prairie, start by locating the belt tensioner pulley. Use a wrench or a specialized belt tensioner tool to relieve tension on the belt. Slide the old belt off the pulleys, taking note of the routing path. Install the new belt following the same path, ensuring it is properly seated on each pulley. Finally, release the tensioner to apply tension to the new belt. Detailed steps and diagrams can be found in the Nissan Prairie automotive repair manual.

How do I replace the air filter in a Nissan Prairie?

To replace the air filter in a Nissan Prairie, open the hood and locate the air filter housing. Unfasten the clips or screws securing the housing and remove the cover. Take out the old air filter and inspect it for dirt or damage. If necessary, replace it with a new one of the same size and type. Clean any debris from the housing, then reattach the cover and secure it properly. For detailed instructions, consult the Nissan Prairie automotive repair manual.

How do I replace the brake pads in a Nissan Prairie?

To replace the brake pads in a Nissan Prairie, start by lifting the vehicle and removing the wheels to gain access to the brake calipers. Use a suitable tool to compress the caliper pistons, then remove the caliper bolts and carefully lift off the caliper. Take out the old brake pads and inspect the caliper and rotor for any signs of damage or excessive wear. Install the new brake pads, ensuring they are properly aligned, and reassemble the caliper. Repeat the process for each wheel, following the specifications and procedures outlined in the Nissan Prairie automotive repair manual.

How do I replace the serpentine belt in a Nissan Prairie?

To replace the serpentine belt in a Nissan Prairie, start by locating the belt tensioner pulley. Use a wrench or a specialized belt tensioner tool to relieve tension on the belt. Slide the old belt off the pulleys, taking note of the routing path. Install the new belt following the same path, ensuring it is properly seated on each pulley. Finally, release the tensioner to apply tension to the new belt. Detailed steps and diagrams can be found in the Nissan Prairie automotive repair manual.

How do I reset the check engine light on a Nissan Prairie?

Resetting the check engine light on a Nissan Prairie can be done by using an OBD-II scanner. Connect the scanner to the diagnostic port, usually located under the dashboard. Follow the scanner's instructions to retrieve and clear the trouble codes. If the issue has been resolved, clearing the codes should turn off the check engine light. If the light persists, further diagnostic steps may be necessary, and it is recommended to consult the Nissan Prairie automotive repair manual for specific troubleshooting procedures.

How do I troubleshoot an electrical issue in a Nissan Prairie?

Troubleshooting electrical issues in a Nissan Prairie can be complex, but the automotive repair manual provides a systematic approach. Start by checking the fuses and relays related to the affected electrical system. Inspect the wiring for any visible damage or loose connections. Use a multimeter to check for continuity and voltage at different points in the circuit. If necessary, consult the wiring diagrams and component locations provided in the Nissan Prairie automotive repair manual to accurately diagnose and repair the electrical issue.

What are the recommended tire pressures for a Nissan Prairie?

The recommended tire pressures for a Nissan Prairie can be found in the automotive repair manual. Generally, the tire pressures vary depending on the specific model and tire size. It is important to maintain the correct tire pressure to ensure optimal performance, handling, and fuel efficiency. Refer to the manual for the precise recommended tire pressures for your Nissan Prairie.

Nissan Prairie Manuals Index

Nissan Prairie Workshop Manual

Related Models