Oldsmobile Cutlass Workshop Manuals and Repair Manuals
Every Manual available online - found by our community and shared for FREE. Enjoy!
The Oldsmobile Cutlass is a line of automobiles made by the Oldsmobile division of General Motors. The Cutlass began as a unibody compact car, but saw its greatest success as a body-on-frame intermediate car. Introduced in 1961 as the top trim level in Olds' compact F-85 line, over the years the Cutlass name accumulated great brand equity, and became one of the most popular nameplates in the industry in the 1970s. The first Oldsmobile Cutlass was an experimental sports coupe designed in 1954. It rode a 110 in (2,800 mm) wheelbase, and had a dramatic fastback roofline, with a stock V8. Its platform was quite similar to the later compact F-85, which was not introduced for seven more years.
Oldsmobile Cutlass FAQ's
Can I use regular gasoline in my Oldsmobile Cutlass?
It is generally recommended to use unleaded gasoline with an octane rating of 87 or higher in your Oldsmobile Cutlass. Using a lower octane fuel may result in engine knocking or pinging, which can lead to damage over time. However, it is always best to consult the owner's manual or consult with a professional to determine the specific fuel requirements for your vehicle.
How do I change the oil in my Oldsmobile Cutlass?
To change the oil in your Oldsmobile Cutlass, first, locate the oil drain plug underneath the car and place a drain pan underneath it. Then, remove the oil drain plug and let the old oil drain completely. Finally, replace the drain plug and refill the engine with the recommended amount of oil, making sure to check the oil level using the dipstick.
How do I check the transmission fluid level in my Oldsmobile Cutlass?
To check the transmission fluid level in your Oldsmobile Cutlass, start the engine and let it warm up to operating temperature. Then, locate the transmission dipstick, typically labeled with a bright color. Remove the dipstick, wipe it clean, reinsert it fully, and then remove it again to check the fluid level. The fluid should be within the designated range on the dipstick.
How do I diagnose a faulty alternator in my Oldsmobile Cutlass?
Diagnosing a faulty alternator in your Oldsmobile Cutlass can be done by performing a simple test using a multimeter. Start by checking the battery voltage with the engine off, then start the engine and measure the voltage again. If the voltage does not increase, or if it drops significantly when electrical loads are applied, it may indicate a faulty alternator. However, for a more accurate diagnosis, it is best to consult an automotive repair manual or seek professional assistance.
How do I replace a burnt-out headlight in my Oldsmobile Cutlass?
To replace a burnt-out headlight in your Oldsmobile Cutlass, first, locate the headlight assembly behind the respective housing. Remove the electrical connector and any retaining clips or screws holding the assembly in place. Then, carefully remove the old bulb and replace it with a new one of the same type. Finally, reassemble the headlight assembly and test the functionality.
How do I replace a damaged power window motor in my Oldsmobile Cutlass?
To replace a damaged power window motor in your Oldsmobile Cutlass, first, remove the interior door panel to gain access to the window mechanism. Disconnect the electrical connector from the motor and remove any mounting screws or bolts securing it in place. Then, carefully remove the old motor and replace it with a new one. Reassemble the door panel and test the functionality of the power window.
How do I replace a faulty fuel pump in my Oldsmobile Cutlass?
To replace a faulty fuel pump in your Oldsmobile Cutlass, first, locate the fuel pump assembly, typically located inside the fuel tank. Disconnect the electrical connector and any fuel lines attached to the assembly. Then, remove any retaining clips or bolts securing the assembly and carefully remove it from the tank. Replace the old fuel pump with a new one and reinstall the assembly, ensuring all connections are properly secured.
How do I replace a malfunctioning brake light in my Oldsmobile Cutlass?
To replace a malfunctioning brake light in your Oldsmobile Cutlass, first, open the trunk and locate the access panel behind the respective brake light assembly. Remove the panel to gain access to the bulb socket. Twist the socket counterclockwise to remove it, then remove the old bulb and replace it with a new one. Reinstall the socket, panel, and test the brake light.
How do I replace a worn-out serpentine belt in my Oldsmobile Cutlass?
To replace a worn-out serpentine belt in your Oldsmobile Cutlass, first, locate the belt tensioner and use a wrench or socket to relieve tension on the belt. Then, carefully remove the old belt from the pulleys, making note of the belt routing. Install the new belt by following the correct routing pattern, ensuring it is properly seated on each pulley. Finally, release the tensioner to apply proper tension to the belt.
How do I reset the maintenance light on my Oldsmobile Cutlass?
To reset the maintenance light on your Oldsmobile Cutlass, first, turn the ignition switch to the "on" position without starting the engine. Then, fully press and release the accelerator pedal three times within five seconds. The maintenance light should start flashing, indicating that the reset process is complete. Turn off the ignition and start the engine to verify if the light has been reset.
How do I troubleshoot a faulty ignition system in my Oldsmobile Cutlass?
Troubleshooting a faulty ignition system in your Oldsmobile Cutlass can involve various steps, including checking for loose connections, inspecting the ignition coil, testing the spark plugs and wires, and verifying the functionality of the ignition switch. If you are experiencing issues such as difficulty starting the engine or misfires, it is advisable to consult an automotive repair manual or seek assistance from a qualified mechanic to accurately diagnose and fix the problem.
How do I troubleshoot a malfunctioning air conditioning system in my Oldsmobile Cutlass?
Troubleshooting a malfunctioning air conditioning system in your Oldsmobile Cutlass can involve checking for refrigerant leaks, inspecting the compressor clutch, testing the pressure sensors, and verifying the functionality of the blower motor and controls. If your air conditioning system is not cooling properly or not working at all, it is advisable to consult an automotive repair manual or seek assistance from a qualified technician to accurately diagnose and repair the issue.
How often should I replace the air filter in my Oldsmobile Cutlass?
The air filter in your Oldsmobile Cutlass should be replaced approximately every 12,000 to 15,000 miles, or as recommended by the manufacturer. A dirty or clogged air filter can restrict airflow to the engine, leading to reduced performance and fuel efficiency. Regularly inspecting and replacing the air filter will help ensure proper engine function.
What is the recommended tire pressure for my Oldsmobile Cutlass?
The recommended tire pressure for your Oldsmobile Cutlass can typically be found in the owner's manual or on a sticker located on the driver's side door jamb. It is important to maintain the proper tire pressure for optimal handling, fuel efficiency, and tire longevity. Be sure to check the tire pressure regularly and adjust it as needed.
What type of engine oil should I use in my Oldsmobile Cutlass?
The type of engine oil you should use in your Oldsmobile Cutlass will depend on the specific engine model. Consult the owner's manual or a professional to determine the recommended viscosity and oil specifications for your vehicle. It is important to use the correct oil to ensure optimal engine performance and longevity.
Get notified for new manuals?
We'll send you a quick email when a new Oldsmobile Cutlass manual is added.