Peugeot 2008 Workshop Manuals and Repair Manuals

To adjust the headlights in a Peugeot 2008, park the vehicle on a level surface facing a wall or garage door. Measure the distance between the ground and the center of each headlight, and mark this height on the wall. Back the vehicle up approximately 25 feet and turn on the headlights. Using the adjustment screws located on the back of the headlight assembly, align the beams so that they hit the marked height on the wall.

To change the oil in a Peugeot 2008, start by locating the oil drain plug underneath the engine. Remove the plug and let the old oil drain into a suitable container. Once the oil has fully drained, replace the drain plug and refill the engine with the recommended oil grade and quantity specified in the owner's manual.

To check the brake fluid level in a Peugeot 2008, locate the brake fluid reservoir under the hood on the driver's side. The reservoir is typically transparent or translucent, allowing you to easily see the fluid level. Ensure the vehicle is on level ground and check that the fluid level is between the minimum and maximum marks on the reservoir. If needed, add the recommended brake fluid to bring the level within the specified range.

To check the transmission fluid level in a Peugeot 2008, start by parking the vehicle on a level surface and ensuring the engine is at operating temperature. Locate the transmission dipstick, usually found near the back of the engine bay. Remove the dipstick, wipe it clean, reinsert it, and then remove it again to check the fluid level. The level should be within the designated range marked on the dipstick.

To replace a flat tire on a Peugeot 2008, first locate the jack and spare tire in the trunk. Position the jack under the vehicle's designated lift points and raise the car until the flat tire is off the ground. Remove the lug nuts, take off the flat tire, and replace it with the spare tire. Secure the lug nuts, lower the vehicle, and then tighten the lug nuts to the recommended torque specification.

To replace a headlight bulb in a Peugeot 2008, open the hood and locate the rear of the headlight assembly. Twist the bulb socket counterclockwise to remove it from the assembly. Gently pull out the old bulb and insert the new bulb, being careful not to touch the glass with bare fingers. Reinsert the bulb socket into the assembly, twist it clockwise to secure it, and test the headlights to ensure proper operation.

To replace a windshield wiper blade in a Peugeot 2008, lift the wiper arm away from the windshield and locate the release tab on the wiper blade. Depress the tab and slide the blade out of the wiper arm. Position the new wiper blade into the wiper arm, ensuring it clicks securely into place. Gently lower the wiper arm back onto the windshield, and repeat the process for the other wiper blade if necessary.

To replace the battery in a Peugeot 2008, first, ensure the vehicle is turned off and the ignition key is removed. Locate the battery, usually located in the engine bay or trunk. Disconnect the negative (black) battery cable followed by the positive (red) cable, being careful to avoid any contact between the two terminals. Remove any retaining brackets or clamps, then lift out the old battery and replace it with a new one of the same size and specifications. Reconnect the positive cable followed by the negative cable, ensuring they are securely tightened.

To replace the cabin air filter in a Peugeot 2008, start by locating the filter housing, usually located behind the glove box or under the dashboard. Open the housing and remove the old filter by sliding it out. Clean any debris or dust from the housing, then insert the new filter in the correct direction as indicated by the arrow on the filter. Close the housing, ensuring it is securely fastened, and test the airflow through the vents to confirm proper installation.

To reset the service light on a Peugeot 2008, turn the ignition on without starting the engine. Press and hold the trip reset button on the instrument cluster until the service light begins to flash. Release the button, then press and hold it again until the light remains illuminated. Finally, turn off the ignition, wait a few seconds, and then start the engine to verify that the service light has been reset.

If you are experiencing electrical issues in your Peugeot 2008, start by checking the fuse box for any blown fuses related to the problem. Inspect the wiring harnesses and connectors for any signs of damage or loose connections. If needed, consult the vehicle's wiring diagram and use a multimeter to test for proper voltage and continuity. If the issue persists, it is recommended to seek the assistance of a qualified automotive electrician or a Peugeot dealership for further diagnosis and repair.

If your Peugeot 2008 is experiencing overheating issues, first check the coolant level and ensure it is at the recommended level. Inspect the radiator for any signs of blockage or leaks, and clean or repair as necessary. Additionally, check the operation of the cooling fans, thermostat, and water pump. If the issue persists, it is advisable to consult a professional mechanic for further diagnosis and repair.

The recommended interval for replacing spark plugs in a Peugeot 2008 can vary depending on the specific engine and the type of spark plugs used. Generally, it is advised to replace spark plugs every 30,000 to 100,000 miles or as specified in the owner's manual. However, it's important to regularly inspect the spark plugs for signs of wear or fouling and replace them if necessary.

In a Peugeot 2008, it is recommended to use a coolant that meets the specifications outlined in the owner's manual. Typically, a coolant with a mix of ethylene glycol and water in a 50:50 ratio is suitable for most climates. It is essential to use the correct coolant to ensure efficient engine cooling and prevent any potential damage to the cooling system.