Peugeot 306 Workshop Manuals and Repair Manuals
Every Manual available online - found by our community and shared for FREE. Enjoy!
Peugeot 306
The Peugeot 306 was a small family car from the French manufacturer Peugeot from 1993 to 2002. Peugeot gave the 306 manyupdates and aesthetic changes to keep up the competition but it was replaced by the 307 in 2001. Cabriolet and estate versions continued until 2002. Versions were built in Argentina by Sevel (1996 2002). It was mechanically very much identical to the Citroen ZX, which entered the market in 1991. It participated in several motorsports and won the Spa 24 hours endurance race in 1999 and 2000. In the 2006 Australian Used Car Safety Ratings, the Peugeot 306 manufactured between 1994 and 2001 was rated "significantly better than average" which was a very good result for that time.Peugeot 306 FAQ's
How do I adjust the headlights on a Peugeot 306?
To adjust the headlights on a Peugeot 306, park the vehicle on a level surface facing a wall or garage door. Measure the distance between the ground and the center of the headlight lens for both headlights. Using a screwdriver or an appropriate adjustment tool, locate the vertical and horizontal adjustment screws on each headlight assembly and adjust them accordingly to align the headlights with the desired height and direction.
How do I bleed the brakes on a Peugeot 306?
To bleed the brakes on a Peugeot 306, start by locating the brake bleeder valves on each caliper or wheel cylinder. Then, attach a clear plastic tube to the bleeder valve and place the other end in a container to collect the brake fluid. Have a helper pump the brake pedal several times, then open the bleeder valve to release any air bubbles. Repeat this process until all air is purged and only clean brake fluid comes out.
How do I change the oil and oil filter on a Peugeot 306?
Changing the oil and oil filter on a Peugeot 306 can be done by first locating the drain plug underneath the engine and placing a drain pan beneath it. Remove the drain plug and allow the old oil to drain completely. Then, remove the old oil filter and replace it with a new one. Finally, reinstall the drain plug and fill the engine with the recommended amount of fresh oil.
How do I diagnose a misfire in a Peugeot 306?
To diagnose a misfire in a Peugeot 306, start by connecting a scan tool to the vehicle's OBD-II port to retrieve any stored trouble codes. If a misfire code is present, inspect the spark plugs, ignition coils, and fuel injectors for any signs of damage or malfunction. Additionally, check the engine's compression levels and perform a cylinder leak-down test to identify any internal engine issues.
How do I replace the alternator on a Peugeot 306?
To replace the alternator on a Peugeot 306, start by disconnecting the negative battery cable and removing the drive belt. Then, disconnect the electrical connectors and mounting bolts securing the alternator in place. Finally, install the new alternator by reversing the steps taken to remove the old one, ensuring all connections are securely fastened.
How do I replace the brake pads on a Peugeot 306?
To replace the brake pads on a Peugeot 306, start by loosening the lug nuts on the wheel, then raise the vehicle and remove the wheel. Locate the brake caliper and remove the bolts securing it to the caliper bracket. Slide the caliper off the rotor and remove the old brake pads. Install the new brake pads, ensuring they are properly aligned, and reassemble the caliper onto the bracket. Finally, reinstall the wheel and tighten the lug nuts.
How do I replace the fuel filter on a Peugeot 306?
To replace the fuel filter on a Peugeot 306, start by relieving the fuel system pressure by removing the fuel pump fuse or relay and running the engine until it stalls. Locate the fuel filter, usually mounted along the fuel line, and use a wrench to loosen the fittings on both ends of the filter. Remove the old filter and replace it with a new one, ensuring the fittings are tightened securely.
How do I replace the radiator on a Peugeot 306?
To replace the radiator on a Peugeot 306, start by draining the coolant from the radiator by opening the drain plug or removing the lower radiator hose. Disconnect the upper and lower radiator hoses, as well as any electrical connections or brackets securing the radiator in place. Finally, remove the old radiator and install the new one, reconnecting all hoses, connections, and brackets.
How do I replace the serpentine belt on a Peugeot 306?
To replace the serpentine belt on a Peugeot 306, locate the tensioner pulley and use a wrench or socket to rotate it counterclockwise, releasing tension on the belt. Slide the old belt off the pulleys and carefully route the new belt around the pulleys according to the belt routing diagram. Finally, release the tensioner pulley to apply tension to the new belt.
How do I replace the spark plugs on a Peugeot 306?
To replace the spark plugs on a Peugeot 306, start by locating the spark plugs wires or ignition coil packs. Disconnect the wires or coil packs from the spark plugs and remove them using a spark plug socket and ratchet. Inspect the condition of the old spark plugs and replace them with new ones, tightening them to the recommended torque specifications.
How do I reset the check engine light on a Peugeot 306?
Resetting the check engine light on a Peugeot 306 can be done by using an OBD-II scan tool to clear any stored trouble codes. Connect the scan tool to the OBD-II port and follow the tool's instructions to access the diagnostic menu and clear the codes. Alternatively, disconnecting the vehicle's battery for a few minutes may also reset the check engine light.
How do I troubleshoot a non-starting Peugeot 306?
When troubleshooting a non-starting Peugeot 306, check the battery for a proper charge and inspect the battery terminals for any corrosion or loose connections. Ensure the vehicle is in park or neutral and try jump-starting the car. If it still does not start, check the ignition system for spark and the fuel system for proper fuel delivery. If necessary, consult the Peugeot 306 repair manual for further guidance.
How do I troubleshoot an electrical issue in a Peugeot 306?
When troubleshooting an electrical issue in a Peugeot 306, begin by checking the fuse box for any blown fuses related to the malfunctioning component. If the fuses are intact, proceed to inspect the wiring and connections for any signs of damage or loose connections. Utilize a multimeter to test for continuity and voltage at various points in the circuit to identify the source of the problem.
What are the common causes of overheating in a Peugeot 306?
Common causes of overheating in a Peugeot 306 may include a malfunctioning thermostat, a faulty radiator, a damaged water pump, or low coolant levels. It is important to inspect these components and address any issues to prevent further damage to the engine.
Peugeot 306 on Amazon
Peugeot 306 Workshop Manual
-
- Peugeot 306 1993 1996 Workshop Manual
- (319 Pages)
- (Free)
-
- Peugeot 306 Workshop Manual Russian
- (128 Pages)
- (Free)
-
- Peugeot 306 Workshop Manual Spanish
- (168 Pages)
- (Free)
Peugeot 306 Owners Manual
-
- Peugeot 306 Owners Manual Russian
- (117 Pages)
- (Free)
-
- Peugeot 306 Owners Manual Russian Cabrio
- (133 Pages)
- (Free)
Related Models