Peugeot 406 Workshop Manuals and Repair Manuals
Every Manual available online - found by our community and shared for FREE. Enjoy!
Peugeot 406
Successor to the Peugeot 405 and predecessor to the Peugeot 406, this car, from the French automaker Peugeot, enjoyed a nine-year ride between 1995 and 2004. It used the same platform as the Citroën Xantia, though without that car's sophisticated hydropneumatic suspension system. Available in saloon, estate and coupé bodystyles with a choice of petrol or turbodiesel engines, the 406 replaced the Peugeot 405 in Peugeot's lineup, the later gained particular favour, and became one of Europe s most-popular diesel brands. It was awarded 1996 What Car Magazine s Car of the Year . Laurent Aiello won the 1997 Super Tourenwagen Cup season driving a 406.Peugeot 406 FAQ's
How do I change the oil in a Peugeot 406?
To change the oil in a Peugeot 406, start by locating the oil drain plug underneath the engine and removing it. Allow the old oil to completely drain into a suitable container. Once drained, replace the drain plug and add the recommended amount of fresh oil through the oil filler cap on top of the engine. Be sure to use the correct oil viscosity and follow the recommended oil change interval specified in the Peugeot 406 automotive repair manual.
How do I check the transmission fluid level in a Peugeot 406?
To check the transmission fluid level in a Peugeot 406, start by locating the transmission dipstick, which is typically situated near the engine. With the engine running and the transmission warmed up, insert the dipstick fully into the transmission and then remove it. Check the fluid level indicated on the dipstick against the recommended range specified in the Peugeot 406 automotive repair manual. If the fluid level is low, add the appropriate type of transmission fluid through the dipstick tube, being careful not to overfill.
How do I replace a headlight bulb on a Peugeot 406?
To replace a headlight
How do I replace the air filter on a Peugeot 406?
To replace the air filter on a Peugeot 406, locate the air filter housing, which is usually situated in the engine compartment. Open the housing by removing the clips or screws that secure it. Take out the old air filter and clean any debris from the housing. Install a new air filter that matches the dimensions and specifications outlined in the Peugeot 406 automotive repair manual. Make sure the filter is properly seated and secure the housing back in place.
How do I replace the brake pads on a Peugeot 406?
To replace the brake pads on a Peugeot 406, start by safely lifting the vehicle and removing the wheels. Locate the brake caliper and remove the bolts securing it to the brake disc. Once the caliper is loose, carefully remove the old brake pads and replace them with new ones. Before reassembling, it is recommended to clean and lubricate the caliper slides and ensure the brake disc is in good condition. Detailed step-by-step instructions can be found in the Peugeot 406 automotive repair manual.
How do I replace the fuel filter on a Peugeot 406?
To replace the fuel filter on a Peugeot 406, start by locating the fuel filter, which is typically located along the fuel line underneath the vehicle. Ensure the engine is cool and relieve the fuel system pressure by removing the fuel pump fuse or relay and running the engine until it stalls. Once the pressure is relieved, use appropriate wrenches or tools to disconnect the fuel lines from the filter. Remove the old filter and install a new one that matches the specifications provided in the Peugeot 406 automotive repair manual. Reconnect the fuel lines, reinstall the fuel pump fuse or relay, and start the engine to check for any fuel leaks.
How do I replace the serpentine belt on a Peugeot 406?
To replace the serpentine belt on a Peugeot 406, start by locating the belt routing diagram, which is usually found in the engine compartment or in the Peugeot 406 automotive repair manual. Use a suitable tool to relieve tension on the belt tensioner, allowing the belt to be easily removed from the pulleys. Carefully thread the new serpentine belt onto the pulleys following the correct routing indicated in the diagram or manual. Once properly installed, release the tensioner to apply proper tension to the belt.
How do I replace the spark plugs on a Peugeot 406?
To replace the spark plugs on a Peugeot 406, start by identifying the location of the spark plugs, which are usually located on top of the engine's cylinder head. Disconnect the ignition coil or spark plug wires, then use a spark plug socket and ratchet to remove the old spark plugs. Before installing the new spark plugs, ensure they are the correct type and gap them according to the specifications provided in the Peugeot 406 automotive repair manual. Carefully thread the new spark plugs into place, tighten them to the recommended torque, and reconnect the ignition coil or spark plug wires.
How do I replace the timing belt on a Peugeot 406?
Replacing the timing belt on a Peugeot 406 is a complex procedure and requires careful attention to detail. It is recommended to consult the Peugeot 406 automotive repair manual for specific step-by-step instructions and to ensure you have the necessary tools and expertise. In general, the process involves aligning the engine's timing marks, removing the old timing belt cover, tensioner, and idler pulleys, and carefully replacing the timing belt. After installation, it is crucial to verify the correct alignment of the timing marks and perform any required tension adjustments following the instructions provided in the manual.
How do I replace the windshield wiper blades on a Peugeot 406?
To replace the windshield wiper blades on a Peugeot 406, lift the wiper arm away from the windshield and locate the release tab or button on the wiper blade assembly. Depress the tab or button and slide the old wiper blade out of the wiper arm. Align the new wiper blade's adapter with the wiper arm's hook or pin, then firmly press the new blade onto the arm until it clicks into place. Test the wiper blades to ensure they are securely attached and provide proper wiping action.
How do I reset the service indicator on a Peugeot 406?
To reset the service indicator on a Peugeot 406, insert the ignition key and turn it to the "On" position without starting the engine. Within a few seconds, press and hold the "Trip" button on the instrument cluster until the service indicator light begins to flash. Release the button and turn the ignition key to the "Off" position. Start the engine, and the service indicator should be reset. If the indicator does not reset, refer to the Peugeot 406 automotive repair manual for specific instructions or consult a qualified technician.
How do I troubleshoot an electrical issue in a Peugeot 406?
When troubleshooting an electrical issue in a Peugeot 406, it is important to start by checking the fuses and relays related to the problematic circuit. Inspect the wiring harness for any visible damage or loose connections. Use a multimeter to test the continuity and voltage at various points along the circuit. If necessary, consult the electrical diagrams and diagnostic procedures outlined in the Peugeot 406 automotive repair manual for further guidance. If the issue persists, it may be advisable to seek the assistance of a qualified automotive electrician.
How do I troubleshoot an engine misfire in a Peugeot 406?
When troubleshooting an engine misfire in a Peugeot 406, start by checking for any stored diagnostic trouble codes (DTCs) using a suitable scan tool. Inspect the ignition system components, such as the spark plugs, ignition coils, and spark plug wires, for any signs of damage or wear. Verify the fuel delivery system, including the fuel injectors and fuel pressure, to ensure proper fuel supply. Additionally, check the engine's compression levels and perform a thorough inspection of the intake and exhaust systems. Detailed diagnostic procedures can be found in the Peugeot 406 automotive repair manual.
What are the recommended tire pressures for a Peugeot 406?
The recommended tire pressures for a Peugeot 406 can vary depending on the model and specific tire size. However, as a general guideline, you can refer to the tire pressure specifications listed in the Peugeot 406 automotive repair manual. These specifications will typically provide the recommended tire pressures for both the front and rear tires, as well as for different load conditions. It is important to regularly check and adjust the tire pressures to ensure optimal safety and performance.
What is the recommended coolant for a Peugeot 406?
The recommended coolant for a Peugeot 406 is typically an ethylene glycol-based coolant with a suitable mixture of antifreeze and water. It is important to use a coolant that meets the specifications outlined in the Peugeot 406 automotive repair manual, as this ensures proper cooling system performance and protection against freezing and overheating. The manual will also provide guidance on the correct coolant-to-water ratio for different climates.
Peugeot 406 on Amazon
Peugeot 406 Owners Manual
-
- Peugeot 406 Owners Manual Russian
- (160 Pages)
- (Free)
Related Models
