Pontiac Pursuit Workshop Manuals and Repair Manuals

To change the air filter on a Pontiac Pursuit, start by locating the air filter housing, which is usually a rectangular box near the engine. Unclip or unscrew the housing cover to reveal the old air filter. Remove the old air filter and clean out any debris or dirt from the housing. Then, insert a new air filter that matches the size and specifications of the old one. Finally, secure the housing cover back in place, ensuring a proper seal.

To change the oil in your Pontiac Pursuit, start by locating the oil drain plug underneath the vehicle. Once you've located it, place an oil pan underneath the drain plug and remove the plug to let the old oil drain out completely. After draining, replace the drain plug and proceed to refill the engine with the recommended amount of fresh oil, using the oil filler cap on top of the engine.

To check the engine oil level on a Pontiac Pursuit, park the vehicle on a level surface and ensure the engine is turned off. Open the hood and locate the engine oil dipstick, which is usually indicated by a brightly colored handle. Remove the dipstick, wipe it clean with a cloth, and reinsert it back into the dipstick tube. Then, pull it out again and observe the oil level. The oil level should be between the "MIN" and "MAX" markings on the dipstick. If the level is below the "MIN" mark, add the recommended oil to bring it to the proper level.

To jump-start a Pontiac Pursuit, you will need a set of jumper cables and another vehicle with a charged battery. Start by positioning the two vehicles close enough for the jumper cables to reach both batteries. Then, connect one end of the positive (red) jumper cable to the positive terminal of the dead battery, and the other end to the positive terminal of the charged battery. Next, connect one end of the negative (black) jumper cable to the negative terminal of the charged battery, and the other end to a metal surface on the engine block of the dead vehicle, away from the battery. Once all connections are secure, start the engine of the vehicle with the charged battery, then start the Pontiac Pursuit. After the vehicle has started, carefully disconnect the jumper cables in the reverse order of connection.

To replace a headlight bulb on a Pontiac Pursuit, start by opening the hood and locating the back of the headlight assembly. Depending on the specific model year, you may need to remove a dust cover or access panel to reach the bulb socket. Once you have access to the bulb socket, twist it counterclockwise to remove it, then carefully remove the old bulb and replace it with a new one. Finally, reinstall the bulb socket into the headlight assembly, ensuring it is securely in place.

To replace the cabin air filter on a Pontiac Pursuit, locate the cabin air filter housing, which is typically located behind the glove compartment or under the dashboard. Open the housing and remove the old cabin air filter, making note of its orientation for proper installation of the new filter. Clean out any debris or dust from the housing, then insert a new cabin air filter that matches the size and specifications of the old one. Finally, secure the housing back in place, ensuring a proper seal.

To replace the serpentine belt on a Pontiac Pursuit, start by locating the belt routing diagram, which is typically located on the engine compartment or in the owner's manual. Use the diagram as a reference for the correct belt routing. Then, locate the belt tensioner pulley and use a wrench or serpentine belt tool to relieve tension on the belt. Slide the old belt off the pulleys, and carefully install the new belt following the routing diagram. Finally, release the tensioner to tighten the new belt, ensuring it is properly seated on all pulleys.

To replace the spark plugs on a Pontiac Pursuit, start by locating the spark plug wires or ignition coil packs, depending on the specific engine configuration. Carefully remove the wires or coil packs to access the spark plugs. Use a spark plug socket and ratchet to remove the old spark plugs from the cylinder head. Before installing the new spark plugs, make sure they are properly gapped according to the specifications in the owner's manual. Then, thread the new spark plugs into the cylinder head by hand, and tighten them using a torque wrench to the recommended torque value. Finally, reinstall the spark plug wires or coil packs, ensuring they are securely connected.

To replace the windshield wipers on a Pontiac Pursuit, start by lifting the wiper arm away from the windshield until it locks into a raised position. Then, locate the small tab or release button near the wiper blade assembly and press it to release the old wiper blade. Slide the old blade out of the wiper arm, and carefully align the new wiper blade with the arm. Push the new blade into place until it clicks or locks securely. Repeat the same process for the other wiper blade, and then lower the wiper arms back onto the windshield.

To reset the maintenance light on a Pontiac Pursuit, start by turning the ignition key to the "ON" position without starting the engine. Then, fully press and release the accelerator pedal three times within five seconds. Afterward, turn the ignition key to the "OFF" position and wait for a few seconds. When you start the engine again, the maintenance light should be reset.

The frequency of brake pad replacement on your Pontiac Pursuit depends on various factors such as driving conditions, driving style, and brake pad material. However, as a general guideline, it is recommended to inspect the brake pads every 12,000 to 15,000 miles and replace them if the thickness is less than 3mm. Regular inspections and maintenance will help ensure the safety and longevity of your brake system.

The recommended coolant for a Pontiac Pursuit is a 50/50 mixture of antifreeze and distilled water. It is important to use a coolant that meets the specifications outlined in the vehicle's owner's manual, typically a Dex-Cool or an equivalent long-life coolant. This coolant mixture provides effective protection against freezing, boiling, and corrosion, helping to maintain proper engine temperature and overall cooling system performance.

The recommended tire pressure for a Pontiac Pursuit can vary depending on the specific model and tire size. However, as a general guideline, it is recommended to maintain a tire pressure between 30 and 35 PSI (pounds per square inch) for most Pontiac Pursuit models. It is important to check and adjust the tire pressure regularly to ensure optimal tire performance, fuel efficiency, and vehicle handling.

The Pontiac Pursuit uses automatic transmission fluid (ATF) type Dexron VI for its transmission. This type of fluid is specifically formulated to meet the requirements of General Motors vehicles, including the Pontiac Pursuit. Dexron VI ATF provides excellent lubrication and heat resistance, ensuring smooth shifting and optimal transmission performance.