Toyota Tundra Workshop Manuals and Repair Manuals

Every Manual available online - found by our community and shared for FREE. Enjoy!

Toyota Tundra

Manufactured in the US since May of 1999, Toyota Tundra was characterized as a full-size pickup truck. The first generation Tundra had many similarities with the older Toyota T100 and the compact Toyota Tacoma. The biggest of those similarities was the shared use of a 3.4-liter V6 engine which was the top of the line engine in both the Tacoma and T100. The V6 engine would serve as the base engine for the Tundra, while a second powerplant, a first for a Toyota truck, a V8 engine sized at 4.7-liters was added to the lineup. Aside from being the first full-size pickup truck built by Toyota, it was also nominated for an award as the North American Truck of the Year, and was also Motor Trend magazine s Truck of the Year in 2000 and 2008.

Toyota Tundra FAQ's

How do I change the oil in a Toyota Tundra?

To change the oil in a Toyota Tundra, begin by warming up the engine, then locate and remove the oil drain plug to drain the old oil. Once the oil has completely drained, replace the drain plug and proceed to remove the oil filter. Install a new oil filter and fill the engine with the recommended amount and type of oil specified in the manual.

How do I check the engine oil level in a Toyota Tundra?

To check the engine oil level in a Toyota Tundra, park the vehicle on level ground and ensure the engine is turned off. Locate the oil dipstick, usually with a yellow handle, and remove it. Wipe the dipstick clean, reinsert it fully, and then remove it again to read the oil level. The oil level should be between the minimum and maximum marks indicated on the dipstick.

How do I replace a battery in a Toyota Tundra?

To replace a battery in a Toyota Tundra, start by turning off the engine and ensuring all electrical accessories are turned off. Locate the battery, usually under the hood or in the trunk, and remove any covers or brackets securing it. Disconnect the negative (-) battery cable first, followed by the positive (+) cable. Remove any additional hold-downs or clamps and lift out the old battery. Install the new battery, reconnect the positive (+) cable first, followed by the negative (-) cable, and secure the battery in place.

How do I replace a cabin air filter in a Toyota Tundra?

To replace a cabin air filter in a Toyota Tundra, locate the filter housing behind the glove compartment. Remove any screws or clips securing the housing and open it to access the filter. Take note of the filter's orientation and remove it from the housing. Install the new filter in the correct orientation, close the housing, and secure it back in place.

How do I replace a cabin air filter in a Toyota Tundra?

How do I replace a fuel filter on a Toyota Tundra?

To replace a fuel filter on a Toyota Tundra, start by relieving the fuel system pressure by disconnecting the fuel pump fuse and running the engine until it stalls. Locate the fuel filter along the fuel line and remove any retaining clips or bolts securing it. Disconnect the fuel lines from the filter, noting their orientation, and install the new filter in the same manner. Reconnect the fuel lines, reinstall any retaining clips or bolts, and restore the fuel system pressure.

How do I replace a headlight bulb on a Toyota Tundra?

To replace a headlight bulb on a Toyota Tundra, start by opening the hood and locating the back of the headlight assembly. Carefully detach the electrical connector from the bulb and remove the bulb's retaining clip or spring. Replace the old bulb with a new one, ensuring it is securely in place. Reconnect the electrical connector and test the headlights to ensure proper functionality.

How do I replace a serpentine belt on a Toyota Tundra?

To replace a serpentine belt on a Toyota Tundra, locate the belt routing diagram under the hood. Use a wrench or tensioner tool to relieve tension on the belt, then remove it from the pulleys. Install the new belt following the correct routing as shown in the diagram. Finally, ensure the belt is properly seated on all pulleys and release the tensioner to apply tension to the belt.

How do I replace a spark plug on a Toyota Tundra?

To replace a spark plug on a Toyota Tundra, start by locating the spark plug wires or ignition coils. Gently disconnect the wire or coil from the spark plug. Use a spark plug socket and ratchet to remove the old spark plug. Install the new spark plug, ensuring it is properly gapped, and tighten it snugly. Finally, reconnect the wire or coil and repeat the process for the remaining spark plugs.

How do I replace a windshield wiper blade on a Toyota Tundra?

To replace a windshield wiper blade on a Toyota Tundra, lift the wiper arm away from the windshield. Locate the release mechanism or tab on the wiper blade assembly and press or squeeze it to release the blade. Slide the old blade off the wiper arm and replace it with a new one, ensuring it securely clicks into place. Gently lower the wiper arm back onto the windshield.

How do I replace the brake pads on a Toyota Tundra?

To replace the brake pads on a Toyota Tundra, start by safely lifting the vehicle and removing the wheels. Locate the brake caliper and remove the bolts holding it in place. Carefully remove the worn brake pads and replace them with new ones. Reinstall the caliper, tighten the bolts, and repeat the process for the remaining wheels, ensuring proper torque specifications.

How do I reset the maintenance light on a Toyota Tundra?

To reset the maintenance light on a Toyota Tundra, turn the ignition switch to the "ON" position without starting the engine. Locate the trip meter reset button and press and hold it until the maintenance light starts flashing. Release the button and press it again to reset the light. The light should go off, indicating that the maintenance reminder has been successfully reset.

How often should I change the transmission fluid in a Toyota Tundra?

The recommended interval for changing the transmission fluid in a Toyota Tundra varies depending on the model year and driving conditions. However, it is generally advised to change the transmission fluid every 30,000 to 60,000 miles. Regularly checking the fluid level and following the manufacturer's recommendations in the manual is essential for maintaining a healthy transmission.

What is the recommended tire pressure for a Toyota Tundra?

The recommended tire pressure for a Toyota Tundra is usually specified on a label located on the driver's side door jamb. Ensure that the tires are cold and use a tire pressure gauge to adjust the pressure according to the recommended PSI provided in the manual. Proper tire pressure is crucial for optimal performance, fuel efficiency, and tire longevity.

What type of coolant should I use in a Toyota Tundra?

The type of coolant recommended for a Toyota Tundra depends on the model year and engine type. Generally, Toyota specifies the use of ethylene glycol-based coolant with a 50/50 mixture of coolant and distilled water. It is important to consult the manual and use the coolant specified by Toyota to maintain proper cooling system performance and prevent potential damage.

Toyota Tundra Manuals Index

Toyota Tundra Workshop Manual

Toyota Tundra Owners Manual

Toyota Tundra Misc Document

Related Models

Toyota Tundra on Amazon

Toyota Tundra/Sequoia (00-07) (Chilton) (Chilton's Total Car Care Repair Manual)