Volkswagen Corrado Workshop Manuals and Repair Manuals
Every Manual available online - found by our community and shared for FREE. Enjoy!
Volkswagen Corrado
The Volkswagen Corrado was a sports car developed by the German manufacturer Volkswagen, built at the Karmann factory in Osnabrück, Germany. It was designed by Herbert Schäfer, and was produced between 1 September 1988 and 31 July 1995. The Corrado is a three-door hatchback/liftback with a 2+2 seating layout. All models featured an electrically adjustable rear spoiler, which can be raised or lowered by the driver. This car is equipped with 1.8L, 2.0L, 2.8L and 2.9L petrol engines and it is available with five-speed manual or four-speed automatic transmission style. It was described by the Auto Express magazine as Regarded as one of VW s best-ever drive VW s best-ever driver s cars .Volkswagen Corrado FAQ's
How do I bleed the cooling system in a Volkswagen Corrado?
To bleed the cooling system in a Volkswagen Corrado, start with a cold engine and ensure the vehicle
How do I change the air filter in a Volkswagen Corrado?
To change the air filter in a Volkswagen Corrado, open the hood and locate the air filter housing. Unclip the housing and remove the old air filter. Inspect the housing for any debris or dirt and clean it if necessary. Install the new air filter in the housing, ensuring it is properly seated. Reattach the housing and make sure it is securely fastened. Regularly replacing the air filter helps maintain good air flow to the engine, improving performance and fuel efficiency.
How do I check the engine oil level in a Volkswagen Corrado?
To check the engine oil level in a Volkswagen Corrado, park the vehicle on a level surface and wait for the engine to cool down. Locate the dipstick, which is typically yellow or orange, and pull it out. Wipe it clean, reinsert it fully, and then pull it out again. The oil level should be between the minimum and maximum marks on the dipstick. If it's low, add the recommended oil gradually and recheck until it reaches the proper level.
How do I replace a blown fuse in a Volkswagen Corrado?
To replace a blown fuse in a Volkswagen Corrado, locate the fuse box, which is usually found in the engine compartment or on the driver's side dashboard. Use the fuse diagram in the owner's manual or on the fuse box cover to identify the fuse corresponding to the malfunctioning component. Use a fuse puller or a pair of needle-nose pliers to remove the blown fuse and replace it with a new one of the same amperage rating. Ensure the new fuse is properly seated and test the component to see if it is working correctly.
How do I replace a cabin air filter in a Volkswagen Corrado?
To replace a cabin air filter in a Volkswagen Corrado, locate the filter housing, which is usually located behind the glove box or under the dashboard. Open the housing and remove the old cabin air filter. Clean the housing if necessary, and install the new filter, making sure it is properly aligned with the airflow direction indicated on the filter itself. Close the housing and ensure it is securely fastened. Regularly replacing the cabin air filter helps maintain clean air inside the vehicle, improving air quality and preventing odors.
How do I replace a headlight bulb in a Volkswagen Corrado?
To replace a headlight bulb in a Volkswagen Corrado, open the hood and locate the back of the headlight assembly. Disconnect the electrical connector from the bulb by gently pulling it off. Remove the retaining clip or twist the bulb counterclockwise, depending on the specific design. Carefully remove the old bulb and insert the new one, making sure not to touch the glass part with your bare hands. Reattach the retaining clip or twist the bulb clockwise, reconnect the electrical connector, and test the headlights before driving.
How do I replace a serpentine belt in a Volkswagen Corrado?
To replace the serpentine belt in a Volkswagen Corrado, start by locating the belt tensioner, which is typically a spring-loaded pulley. Use a wrench or socket to rotate the tensioner in the direction indicated by the arrow on the tensioner itself. This will relieve tension on the belt, allowing it to be removed. Carefully route the new belt around all the pulleys according to the belt routing diagram found in the engine compartment. Rotate the tensioner again and slide the new belt onto the tensioner pulley. Release the tensioner slowly, ensuring the belt is properly seated on all pulleys.
How do I replace a thermostat in a Volkswagen Corrado?
To replace a thermostat in a Volkswagen Corrado, start by locating the thermostat housing, which is usually connected to the engine block or cylinder head. Drain the coolant to a level below the thermostat housing, then remove any components obstructing access to the housing. Disconnect the hoses or pipes attached to the housing and remove the bolts securing it. Carefully remove the old thermostat and gasket, clean the mating surfaces, and install the new thermostat and gasket. Reassemble the components, refill the coolant, and verify proper operation of the cooling system.
How do I replace a wheel bearing in a Volkswagen Corrado?
To replace a wheel bearing in a Volkswagen Corrado, start by jacking up the vehicle and securing it on jack stands. Remove the wheel, brake caliper, and rotor to access the wheel hub assembly. Disconnect any electrical connectors or ABS sensors attached to the hub assembly. Use a wrench or socket to remove the axle nut, then remove the hub assembly by carefully tapping it with a hammer and a soft drift. Clean the mounting surfaces and install the new wheel bearing, ensuring it is properly seated. Reassemble the components in reverse order and torque all bolts to the recommended specifications.
How do I replace the brake pads on a Volkswagen Corrado?
To replace the brake pads on a Volkswagen Corrado, start by lifting the vehicle and securing it on jack stands. Remove the wheels to access the brake calipers. Use a wrench or socket to remove the caliper bolts and then slide the caliper off the rotor. Remove the old brake pads and use a brake caliper compressor tool to push the caliper piston back into its housing. Install the new brake pads and reassemble the caliper onto the rotor. Repeat the process for all four wheels and ensure proper torque on all bolts before test driving the vehicle.
How do I reset the maintenance light in a Volkswagen Corrado?
To reset the maintenance light in a Volkswagen Corrado, turn the ignition key to the "ON" position, but do not start the engine. Locate the trip reset button on the instrument cluster and press and hold it until the maintenance light starts flashing. Release the button and turn the ignition key to the "OFF" position. Start the engine and verify that the maintenance light is no longer illuminated. This procedure may vary slightly depending on the specific model year, so it is advisable to consult the vehicle's repair manual for precise instructions.
How do I troubleshoot a Volkswagen Corrado if it won't start?
If your Volkswagen Corrado won't start, there are several potential causes to consider. Check the battery connections to ensure they are clean and tightly secured. If the battery is fully charged and the connections are fine, check the starter motor and ignition switch for any signs of malfunction. It is also important to verify that the fuel pump is working properly and that there is fuel in the tank. If these basic checks do not resolve the issue, it is recommended to consult a professional or refer to the vehicle's repair manual for further troubleshooting steps.
How often should I change the oil in a Volkswagen Corrado?
It is recommended to change the oil in a Volkswagen Corrado every 5,000 to 7,500 miles or every 6 months, whichever comes first. Regular oil changes are essential for the proper functioning and longevity of the engine. However, the frequency may vary depending on driving conditions, such as extreme temperatures or heavy loads, so it is advisable to consult the owner's manual for specific recommendations.
What should I do if my Volkswagen Corrado's battery is dead?
If the battery of your Volkswagen Corrado is dead, you can jump-start the vehicle using jumper cables and another vehicle with a working battery. Park the two vehicles close to each other, turn off the engines, and connect the positive (+) terminals of the batteries with a jumper cable. Then, connect the negative (-) terminal of the working battery to a metal part of the dead vehicle, such as a bolt or bracket. Start the engine of the working vehicle and let it run for a few minutes to charge the dead battery. Attempt to start the Volkswagen Corrado. If it starts, let it run for a while to recharge the battery.
What type of coolant should I use in a Volkswagen Corrado?
For a Volkswagen Corrado, it is recommended to use a coolant that meets the G12 or G13 specification. These coolants are specifically formulated to provide optimal corrosion protection and temperature regulation for the engine. Avoid using coolants that do not meet these specifications, as they may not provide the necessary protection and could potentially cause damage to the cooling system.
Volkswagen Corrado Manuals Index
Volkswagen Corrado on Amazon
Volkswagen Corrado Workshop Manual
Volkswagen Corrado Misc Document
Related Models