The Dodge Durango is a mid-size to full size sport utility vehicle (SUV), introduced in 1998 by Dodge division of Chrysler. Since its introduction, three generations of this vehicle have been released.The first two generations were very similar in that both were based on the Dodge Dakota, both featured a body-on-frame construction and both were produced at the Newark Assembly plant in Newark, Delaware. The third generation Durango s features unibody construction and assembled in Detroit, Michigan. The Dodge Durango gained good market in US with 1.4 million units sold until 2013.
Frequently Asked Questions
How do I check and refill the transmission fluid in a 2015 Dodge Durango?
To check and refill the transmission fluid in a 2015 Dodge Durango, first make sure the vehicle is on a level surface and the engine is idling. Then locate the transmission dipstick and remove it. Wipe it clean, reinsert it, and remove it again to check the fluid level. If it is low, add the recommended type of transmission fluid through the dipstick tube.
How do I diagnose a check engine light on a 2009 Dodge Durango?
To diagnose a check engine light on a 2009 Dodge Durango, use an OBD-II scanner to read the diagnostic trouble codes (DTCs) stored in the engine computer. Look up the codes in the repair manual to determine the cause of the issue. Common causes include faulty sensors, emissions issues, and ignition system problems.
How do I replace a cabin air filter on a 2013 Dodge Durango?
To replace a cabin air filter on a 2013 Dodge Durango, first locate the filter housing under the dashboard on the passenger side. Remove the cover and slide out the old filter. Install the new filter, making sure it is oriented correctly, and reattach the cover. It is recommended to replace the cabin air filter every 15,000 miles.
How do I replace a headlight bulb on a 2014 Dodge Durango?
To replace a headlight bulb on a 2014 Dodge Durango, first locate the back of the headlight assembly and unplug the electrical connector. Then release the retaining clip and remove the bulb from the assembly. Install the new bulb, secure it with the retaining clip, and reconnect the electrical connector.
How do I replace a windshield wiper blade on a 2016 Dodge Durango?
To replace a windshield wiper blade on a 2016 Dodge Durango, first lift the wiper arm away from the windshield. Then release the old wiper blade by pressing the release tab and sliding it off the wiper arm. Install the new wiper blade by sliding it onto the arm until it clicks into place.
How do I reset the oil change indicator on a 2010 Dodge Durango?
To reset the oil change indicator on a 2010 Dodge Durango, turn the key to the “on” position without starting the engine. Fully depress the accelerator pedal three times within 10 seconds and then turn the key off. Start the engine and verify that the indicator has been reset.
How do I troubleshoot a starting issue on a 2016 Dodge Durango?
To troubleshoot a starting issue on a 2016 Dodge Durango, first check the battery and connections for corrosion and proper voltage. If the battery is good, check the starter and starter relay for proper operation. If those components are functioning properly, check the ignition switch and wiring for issues.
What is the procedure for replacing the alternator on a 2011 Dodge Durango?
To replace the alternator on a 2011 Dodge Durango, first disconnect the battery and remove the serpentine belt. Then remove the electrical connections and mounting bolts from the alternator and remove it from the vehicle. Install the new alternator and reconnect all electrical connections and the serpentine belt.
What is the procedure for replacing the brake pads on a 2012 Dodge Durango?
To replace the brake pads on a 2012 Dodge Durango, first remove the wheel and caliper. Then compress the caliper piston and remove the old brake pads. Install the new brake pads and reassemble the caliper and wheel. Be sure to properly torque the lug nuts and pump the brakes to ensure proper brake performance.
What is the procedure for replacing the fuel filter on a 2006 Dodge Durango?
To replace the fuel filter on a 2006 Dodge Durango, first relieve the fuel system pressure by disconnecting the fuel pump relay or fuse and running the engine until it stalls. Then disconnect the fuel lines from the filter, remove the mounting bracket, and replace the filter. Reconnect the fuel lines and relay or fuse and start the engine to verify proper operation.
What is the proper procedure for bleeding the brakes on a 2008 Dodge Durango?
To bleed the brakes on a 2008 Dodge Durango, first start with the wheel farthest from the master cylinder and work your way closer. Have a helper pump the brakes and hold pressure on the pedal while you open the bleeder valve. Close the valve and repeat until all air is removed from the system.
What is the proper tire pressure for a 2018 Dodge Durango?
The proper tire pressure for a 2018 Dodge Durango varies depending on the tire size and load capacity. The recommended tire pressure can be found on the tire information placard located on the driver’s side door jamb. It is important to maintain the proper tire pressure for optimal handling, fuel economy, and tire life.
What is the recommended coolant type and capacity for a 2017 Dodge Durango?
The recommended coolant type for a 2017 Dodge Durango is a mixture of ethylene glycol and water with a 50/50 ratio. The coolant capacity for this vehicle is 14.5 quarts. It is important to use the recommended coolant type and capacity to prevent overheating and damage to the engine.
What is the recommended oil type and capacity for a 2019 Dodge Durango?
The recommended oil type for a 2019 Dodge Durango is SAE 5W-20. The oil capacity for this vehicle is 7 quarts. It is important to use the recommended oil type and capacity to ensure optimal engine performance and longevity.
What is the recommended spark plug gap for a 2007 Dodge Durango?
The recommended spark plug gap for a 2007 Dodge Durango varies depending on the engine type. For the 3.7L V6 engine, the gap should be 0.045 inches. For the 4.7L V8 engine, the gap should be 0.040 inches. It is important to use the correct spark plug gap for optimal engine performance.