The Hyundai Starex is a van built by the Hyundai Motor Company in South Korea and Indonesia since 1997. First generation models were known in Europe as the Hyundai H-1 and as the Hyundai H200 in the Netherlands. For the second generation, Australian and UK market models are sold as the Hyundai iLoad (cargo version) and in Australia as Hyundai iMax and the UK as Hyundai i800 (people mover versions). The Starex is also produced in China under the name JAC Refine by Anhui Jianghuai Automobile since 2002 under Hyundai licence. It is very successful, with a market share of about 20 percent.
Frequently Asked Questions
How do I check the transmission fluid level on my Chevrolet Cobalt?
To check the transmission fluid level on your Chevrolet Cobalt, you need to park the car on a level ground and let the engine idle for a few minutes. Then, locate the transmission dipstick, pull it out and wipe it clean with a rag. Finally, reinsert the dipstick and check the fluid level against the markings on the dipstick.
How do I perform a coolant flush on my Chevrolet Cobalt?
To perform a coolant flush on your Chevrolet Cobalt, you need to drain the old coolant from the radiator and engine block, and flush the system with water or a flushing solution. Then, refill the system with a 50/50 mix of coolant and distilled water, and bleed any air pockets from the system. Refer to the repair manual for the specific procedure and coolant type recommended by the manufacturer.
How do I replace the air filter on my Chevrolet Cobalt?
To replace the air filter on your Chevrolet Cobalt, locate the air filter housing, which is usually located on the driver’s side of the engine compartment. Open the housing and remove the old air filter by pulling it out. Then, clean the housing and install the new air filter, making sure it is properly seated and secured.
How do I replace the alternator on my Chevrolet Cobalt?
To replace the alternator on your Chevrolet Cobalt, first disconnect the battery cables and remove the serpentine belt from the alternator pulley. Then, remove the electrical connections and mounting bolts holding the alternator in place. Lift the alternator out of the engine compartment and install the new alternator, making sure to torque the mounting bolts to the specified values. Finally, reconnect the electrical connections and serpentine belt, and test the charging system.
How do I replace the battery on my Chevrolet Cobalt?
To replace the battery on your Chevrolet Cobalt, first remove the negative cable from the battery terminal. Then, remove the hold-down bracket and any other attachments holding the battery in place. Lift the battery out of the tray and install the new battery, making sure to connect the positive and negative cables securely. Finally, test the battery and charging system to ensure proper operation.
How do I replace the brake pads on my Chevrolet Cobalt?
To replace the brake pads on your Chevrolet Cobalt, you need to jack up the car and remove the wheels. Then, remove the caliper bolts and slide out the old brake pads. Clean the caliper and rotor surfaces, and install the new brake pads. Finally, reassemble the caliper and wheel, and repeat the process for the other wheels.
How do I replace the fuel filter on my Chevrolet Cobalt?
To replace the fuel filter on your Chevrolet Cobalt, first relieve the fuel system pressure by disconnecting the fuel pump fuse or relay. Then, locate the fuel filter, which is usually located under the car, near the fuel tank. Remove the old filter and install the new filter, making sure to connect the fuel lines properly. Finally, test the fuel system for leaks and proper operation.
How do I replace the radiator on my Chevrolet Cobalt?
To replace the radiator on your Chevrolet Cobalt, first drain the coolant from the radiator and engine block, and remove any hoses and electrical connections attached to the radiator. Then, remove the mounting bolts and lift the radiator out of the engine compartment. Install the new radiator, making sure to reconnect all hoses and electrical connections, and refill the system with coolant. Finally, test the cooling system for leaks and proper operation.
How do I replace the serpentine belt on my Chevrolet Cobalt?
To replace the serpentine belt on your Chevrolet Cobalt, first locate the belt routing diagram under the hood. Then, use a wrench or tensioner tool to release the tension on the belt, and slide the old belt off the pulleys. Install the new belt, making sure to route it according to the diagram, and release the tensioner. Finally, start the engine and check the belt tension and alignment.
How do I replace the spark plugs on my Chevrolet Cobalt?
To replace the spark plugs on your Chevrolet Cobalt, locate the spark plug wires and disconnect them from the plugs. Then, use a spark plug socket and ratchet to remove the old plugs. Clean the spark plug wells and install the new plugs, making sure to torque them to the specified values. Finally, reconnect the spark plug wires and repeat the process for the other cylinders.
How do I replace the starter on my Chevrolet Cobalt?
To replace the starter on your Chevrolet Cobalt, first disconnect the battery cables and remove any electrical connections and mounting bolts holding the starter in place. Then, lift the starter out of the engine compartment and install the new starter, making sure to torque the mounting bolts to the specified values. Finally, reconnect the electrical connections and battery cables, and test the starting system.
How do I replace the thermostat on my Chevrolet Cobalt?
To replace the thermostat on your Chevrolet Cobalt, first drain the coolant from the system and remove any parts blocking access to the thermostat housing. Then, remove the housing and old thermostat, and clean the mating surfaces. Install the new thermostat, making sure to install it in the correct orientation and torque the housing bolts to the specified values. Finally, refill the system with coolant and test the cooling system for proper operation.
How do I replace the wheel bearings on my Chevrolet Cobalt?
To replace the wheel bearings on your Chevrolet Cobalt, first jack up the car and remove the wheel and brake assembly. Then, remove the axle nut and any other attachments holding the hub assembly in place. Pull the hub assembly off the spindle and remove the old bearings. Install the new bearings and reassemble the hub assembly and brake components. Finally, torque the axle nut to the specified value and test the wheel for proper operation.
What type of oil should I use for my Chevrolet Cobalt?
The type of oil you should use for your Chevrolet Cobalt depends on the engine type and your driving conditions. Refer to the owner’s manual or the recommendation label under the hood for the specific oil grade and viscosity recommended by the manufacturer. In general, synthetic blend or full synthetic oils are preferred for better performance and protection.
Why is my Chevrolet Cobalt’s check engine light on?
There are many reasons why your Chevrolet Cobalt’s check engine light may come on, including issues with the engine, transmission, emissions, or sensors. To determine the exact cause, you need to use a diagnostic tool to read the trouble codes stored in the engine control module. Once you have the codes, you can refer to the repair manual or seek professional help to diagnose and fix the problem.
Chevrolet Cobalt Related Models