Nissan Serena Workshop Manuals and Repair Manuals

Every Manual available online - found by our community and shared for FREE. Enjoy!

Nissan Serena

When launched in 1991 by Nissan Motor Company the Nissan Serena was a compact minivan. Over the years, it grew in size and now it is a five-door van. Earlier versions were front engine, rear-wheel drive layout with a live axle mounted on leaf springs. Later versions had a multilink independent rear suspension, and were front-wheel drive or 4WD. The 2.3L diesel engine variant contains eight seats instead of the usual seven. In European markets, the C23 Serena had 1.6 or 2.0 L petrols, or 2.3 L diesel engines LD23. Trim levels were LX, SLX, SGX and SGXi. Auto Express once named the Serena as the slowest passenger car in the benchmark 0-60 mph (now 62 mph) test, with the 2.3 diesel version (added in the mid 1990s) taking 27.8 seconds to reach that speed.

Nissan Serena FAQ's

How do I change a burnt-out headlight bulb on a Nissan Serena?

To change a burnt-out headlight bulb on a Nissan Serena, first open the hood and locate the back of the headlight assembly. Twist and remove the bulb socket counterclockwise, then carefully pull out the old bulb. Insert the new bulb into the socket, making sure not to touch the glass with your bare hands, as it can cause premature failure. Finally, reinstall the bulb socket by twisting it clockwise until it locks into place.

How do I change the oil filter on a Nissan Serena?

To change the oil filter on a Nissan Serena, first locate the oil filter, which is typically located on the side of the engine block. Use an oil filter wrench to loosen and remove the old filter. Before installing the new filter, make sure to apply a thin layer of oil to the rubber gasket to ensure a proper seal.

How do I check and top up the coolant level in a Nissan Serena?

To check and top up the coolant level in a Nissan Serena, first make sure the engine is cool. Open the hood and locate the coolant reservoir, which is typically a translucent plastic tank with level markings. If the coolant level is below the "MIN" mark, carefully remove the cap and add a mixture of coolant and distilled water until the level reaches the "MAX" mark. It is important to use the correct type of coolant as specified in the owner's manual.

How do I jump-start a Nissan Serena?

To jump-start a Nissan Serena, first position the donor vehicle close to the Serena, with both vehicles turned off. Connect one end of the positive (red) jumper cable to the positive terminal of the discharged battery in the Serena. Connect the other end of the positive jumper cable to the positive terminal of the donor vehicle's battery. Connect one end of the negative (black) jumper cable to the negative terminal of the donor vehicle's battery. Finally, connect the other end of the negative jumper cable to an unpainted metal surface in the engine bay of the Serena, away from the battery. Start the donor vehicle, then start the Serena and let it run for a few minutes before disconnecting the jumper cables.

How do I replace a blown fuse in a Nissan Serena?

To replace a blown fuse in a Nissan Serena, first locate the fuse box, which is typically located in the engine compartment or under the dashboard. Open the fuse box and locate the fuse that corresponds to the malfunctioning component. Use the fuse puller tool or a pair of needle-nose pliers to gently pull out the blown fuse. Insert a new fuse of the same rating into the empty slot, ensuring it is securely seated. Close the fuse box and test the component to verify if the issue has been resolved.

How do I replace a broken side mirror on a Nissan Serena?

To replace a broken side mirror on a Nissan Serena, first remove the interior door panel to access the mirror mounting bolts. Disconnect the electrical wiring harness if applicable. Unscrew the mounting bolts and carefully remove the old mirror. Install the new mirror by reversing the steps, making sure to securely tighten the mounting bolts and reconnect any electrical connectors.

How do I replace a faulty ignition coil on a Nissan Serena?

To replace a faulty ignition coil on a Nissan Serena, first locate the ignition coil(s), which are typically mounted on top of the engine. Disconnect the electrical connector(s) from the faulty coil, then remove the mounting bolts securing the coil to the engine. Carefully lift the coil off the spark plug, being careful not to damage the plug or the coil boot. Install the new ignition coil by reversing the steps, ensuring the electrical connector is securely attached and the mounting bolts are tightened. Repeat the process for any additional faulty ignition coils.

How do I replace the brake pads on a Nissan Serena?

To replace the brake pads on a Nissan Serena, first secure the vehicle on a level surface and set the parking brake. Loosen the lug nuts on the front wheel(s) of the side you are working on. Raise the vehicle using a jack and support it with jack stands. Remove the wheel(s) and locate the brake caliper. Remove the caliper bolts, then carefully lift the caliper off the brake rotor. Slide out the old brake pads and install the new ones, making sure they are properly aligned. Reinstall the caliper, tighten the bolts, and repeat the process for the other side. Finally, reinstall the wheel(s), lower the vehicle, and tighten the lug nuts.

How do I replace the cabin air filter in a Nissan Serena?

To replace the cabin air filter in a Nissan Serena, first locate the cabin air filter housing, which is typically located behind the glove compartment. Open the glove compartment and remove any contents. Release the glove compartment stops and allow it to hang freely. Remove the cabin air filter housing cover, then take out the old filter and replace it with a new one. Reinstall the housing cover, close the glove compartment, and make sure it latches properly.

How do I replace the serpentine belt on a Nissan Serena?

To replace the serpentine belt on a Nissan Serena, first locate the belt routing diagram, which is typically found on the engine cover or in the owner's manual. Use a wrench or a tensioner tool to relieve tension on the belt tensioner, then slide the belt off the pulleys. Install the new belt following the belt routing diagram, ensuring it is properly seated on each pulley. Release the tensioner, allowing it to apply tension to the new belt. Finally, inspect the belt to ensure it is properly aligned and tensioned.

How do I replace the windshield wipers on a Nissan Serena?

To replace the windshield wipers on a Nissan Serena, first lift the wiper arm away from the windshield. Locate the small tab or release button near the wiper blade, then push or slide it to release the old blade. Slide the old blade off the wiper arm and discard it. Align the new wiper blade with the wiper arm, making sure it is securely attached. Gently lower the wiper arm back onto the windshield, ensuring the new blade makes proper contact with the glass. Repeat the process for the other wiper blade.

How do I reset the maintenance reminder light on a Nissan Serena?

To reset the maintenance reminder light on a Nissan Serena, first turn the ignition switch to the "ON" position without starting the engine. Within 10 seconds, fully depress and release the accelerator pedal five times. The maintenance reminder light should start blinking, indicating that it has been reset. Turn off the ignition and start the engine to ensure the light remains off.

How often should I replace the engine air filter in a Nissan Serena?

It is recommended to replace the engine air filter in a Nissan Serena every 15,000 to 30,000 miles, or as specified in the owner's manual. However, if you frequently drive in dusty or dirty conditions, it may be necessary to replace the air filter more frequently. Regularly inspect the air filter for any signs of dirt or damage and replace it if necessary to ensure optimal engine performance and fuel efficiency.

What are the recommended tire pressures for a Nissan Serena?

The recommended tire pressures for a Nissan Serena can vary depending on the specific model and tire size. However, as a general guideline, the recommended tire pressure for the front tires is typically around 32 psi and around 30 psi for the rear tires. It is important to check the owner's manual or the tire placard located on the driver's side door jamb for the exact recommended tire pressures for your specific vehicle.

Nissan Serena Manuals Index

Nissan Serena Workshop Manual

Nissan Serena Owners Manual

Related Models